| https://www.eptac.com/ask/defining-standard-industry-practices-for-torque-of-threaded-fasteners/
. I’ve added a couple of web sites for you to review about what the Torque value should be depending upon the diameter size of the screw, nut or bolt. 1. http
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/news/news/2020-01-13
Useon’s SAT-X 175 co-rotating twin screw extruder. The unit has a 2,000 kW motor and Useon’s patented high-torque gearbox. The throughput of the line is 8 to 10 tons/hour
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/FPC-Pump-Interface-User-Guide-22890001.pdf
Interface to a GPD Global Micro-Dot or HyFlo pump: 1. Screw the FPC Pump Interface mounting bracket (D) to pump body, The shape of the mounting bracket will vary with FPC Pump Interface model; for details refer to References (pg 18). 2. Hand tighten the FPC
GPD Global | https://www.gpd-global.com/pdf/doc/FPC-Pump-Interface-User-Guide-22890001.pdf
Interface to a GPD Global Micro-Dot or HyFlo pump: 1. Screw the FPC Pump Interface mounting bracket (D) to pump body, The shape of the mounting bracket will vary with FPC Pump Interface model; for details refer to References (pg 18). 2. Hand tighten the FPC
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/products/screws/twinshot-mulit-material-molding
screw and barrel product line was recently acquired by Altair Investments. We invite you to visit Xaloy’s new website, www.xaloy.com , to find the most current information. The Xaloy Twinshot®
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/information/upsize-or-downsize
. Consideration of limiting torque to the hydraulic screw drive motor should also be given to reduce the breakage of the smaller screws. Upsizing Is your injection unit too small
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/information/increase-production-rates
. Lower than desired production rates can be the result of numerous areas including; improper screw design, screw and/or barrel wear, high head pressure, limited torque, low-wattage barrel heaters, improper barrel temperature profile, and feed stock bulk density
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Compliant-Conveyor-Crowder-Data-Sheet-22200608.pdf
. The thumb screws act as a stop for the Actuator Shaft (Item 9). Align Conveyor Crowder with Conveyor Rail To adjust the lateral alignment of the conveyor crowder so it is parallel with the conveyor rail, loosen and tighten the cap screw (Item 27) and set screw (Item 35
GPD Global | https://www.gpd-global.com/pdf/doc/Compliant-Conveyor-Crowder-Data-Sheet-22200608.pdf
. The thumb screws act as a stop for the Actuator Shaft (Item 9). Align Conveyor Crowder with Conveyor Rail To adjust the lateral alignment of the conveyor crowder so it is parallel with the conveyor rail, loosen and tighten the cap screw (Item 27) and set screw (Item 35
| https://www.eptac.com/faqs/ask-helena-leo/ask/when-to-tin-and-not-tin-wires
: I have a connector that you insert a 7/30 wire into and hold it in place by tightening a screw. Should the wire be tinned? I have look in my IPC 620 standard and the only reference I see is Section
