Technical Library: seeing (Page 1 of 51)

Void Reduction in Bottom Terminated Components Using Vacuum Assisted Reflow

Technical Library | 2019-07-10 23:36:14.0

Pockets of gas, or voids, trapped in the solder interface between discrete power management devices and circuit assemblies are, unfortunately, excellent insulators, or barriers to thermal conductivity. This resistance to heat flow reduces the electrical efficiency of these devices, reducing battery life and expected functional life time of electronic assemblies. There is also a corresponding increase in current density (as the area for current conduction is reduced) that generates additional heat, further leading to performance degradation.

Heller Industries Inc.

Conductive Adhesive Dispensing, Process Considerations

Technical Library | 1999-08-27 09:24:56.0

Dispensing conductive adhesives in an automated factory environment creates some special challenges. A robust production process starts with understanding the adhesives in their fluid state and which important parameters must be controlled. Developing this understanding requires experience with a large number of materials and valves over time. Common uses of conductive adhesives in surface mount applications, die attach applications, and gasketing are addressed. As vendors of dispensing equipment, the authors see a constant stream of such applications. Dispensing requirements, techniques, and equipment resulting from this experience are discussed. Guidelines for optimizing quality and speed are given.

Nordson ASYMTEK

SMT007-MIRTEC Intelligent Factory Automation Article-November 2020

Technical Library | 2020-12-02 20:36:54.0

Industry 4.0 is a topic of much discussion within the electronics manufacturing industry. Manufacturers and vendors are trying to come to terms with what that means. In the most simplistic of terms, Industry 4.0 is a trend toward automation and data exchange within the manufacturing process. This basically requires connectivity and communication from machine to machine within the manufacturing line. The challenge is to collect data from each of the systems within the line and make that data available to the rest of the machines. Without test and inspection, there is no Industry 4.0. The whole purpose of test and inspection is to collect actionable data that may be used to reduce defects and maximize efficiency within the manufacturing line. The goal is to minimize scrap and get a really good handle on those process parameters that need to be put in place to manufacture products the right way the first time. For maximum efficiency, three inspection systems are required within the production line. These are solder paste inspection (SPI) post-solder deposition, automated optical inspection (AOI) post-placement, and AOI post-reflow. This requires a substantial investment; however, the combination of all three inspection machines is really the only true way to provide feedback for each stage of the manufacturing process.

MIRTEC Corp

An Air-Assisted "Airless" Conformal Coating Process

Technical Library | 1999-08-27 09:18:58.0

A need to move beyond aerosol sprays and dipping leads to a development that answers tough requirements for controlled coverage, low waste, and environmental restrictions.

Nordson ASYMTEK

Making Sense of Accuracy, Repeatability and Specification for Automated Fluid Dispensing Systems

Technical Library | 2013-11-14 10:43:40.0

Understanding accuracy and repeatability is an important step to analyze fluid dispensing system performance. They can also be prone to misinterpretation when reviewing a product specification. A dispensing motion system can be made to perform better or worse under different operating conditions. This article will explain accuracy and repeatability, and how they can be applied to different specifications. It will also discuss key considerations when interpreting accuracy and repeatability for decision making.

Nordson ASYMTEK

The Industry Requirement for 2D and 3D Inspection Technology in a Single AOI Platform

Technical Library | 2012-11-21 18:57:58.0

The continuing evolution toward advanced miniature packaging has led to ever increasing PCB density and complexity. As the manufacturing process becomes progressively more complicated, there is an ever increasing probability for defects to occur on finished PCB assemblies. For years the Automated Optical Inspection (AOI) industry has relied solely upon two-dimensional (2D) inspection principles to test the quality of workmanship on electronic assemblies. While advancements in conventional 2D optical inspection have made this technology suitable for detecting such defects as missing components, wrong components, proper component orientation, insufficient solder, and solder bridges; there is an inherent limitation in the ability to inspect for co-planarity of ultra-miniature chips, leaded device, BGA and LED packages.

MIRTEC Corporation

Dam and Fill Encapsulation for Microelectronic Packages

Technical Library | 1999-08-27 09:29:49.0

Contract packaging houses have to contend with a large mix of die types and products. Flexibility and quick turnaround of package types is a must in this industry. Traditional methods of die encapsulation, (i.e., use of transfer-molding techniques), are only cost effective when producing a large number of components. Liquid encapsulants now provide similar levels of reliability1, and are cost effective...

Nordson ASYMTEK

Fluid Flow Mechanics Key To Low Standoff Cleaning

Technical Library | 2009-09-18 14:42:37.0

In recent years, various studies have been issued on cleaning under low standoff components; most however, with incomplete information. It is essential to revisit and describe the latest challenges in the market, identifying obvious gaps in available information. Such information is crucial for potential and existing users to fully address the cleanliness levels under their respective components. With the emergence of lead-free soldering and even smaller components, new challenges have arisen including cleaning in gaps of less than 1-mil.

ZESTRON Americas

Throughput vs. Wet-Out Area Study for Package on Package (PoP) Underfill Dispensing

Technical Library | 2012-12-17 22:05:22.0

Package on Package (PoP) has become a relatively common component being used in mobile electronics as it allows for saving space in the board layout due to the 3D package layout. To insure device reliability through drop tests and thermal cycling as well as for protecting proprietary programming of the device either one or both interconnect layers are typically underfilled. When underfill is applied to a PoP, or any component for that matter, there is a requirement that the board layout is such that there is room for an underfill reservoir so that the underfill material does not come in contact with surrounding components. The preferred method to dispensing the underfill material is through a jetting process that minimizes the wet out area of the fluid reservoir compared to traditional needle dispensing. To further minimize the wet out area multiple passes are used so that the material required to underfill the component is not dispensed at once requiring a greater wet out area. Dispensing the underfill material in multiple passes is an effective way to reduce the wet out area and decrease the distance that surrounding components can be placed, however, this comes with a process compromise of additional processing time in the underfill dispenser. The purpose of this paper is to provide insight to the inverse relationship that exists between the wet out area of the underfill reservoir and the production time for the underfill process.

Nordson ASYMTEK

Reflow Soldering Processes and Troubleshooting: SMT, BGA, CSP and Flip Chip Technologies

Technical Library | 2021-01-03 19:24:52.0

Reflow soldering is the primary method for interconnecting surface mount technology (SMT) applications. Successful implementation of this process depends on whether a low defect rate can be achieved. In general, defects often can be attributed to causes rooted in all three aspects, including materials, processes, and designs. Troubleshooting of reflow soldering requires identification and elimination of root causes. Where correcting these causes may be beyond the reach of manufacturers, further optimizing the other relevant factors becomes the next best option in order to minimize the defect rate.

SMTnet

  1 2 3 4 5 6 7 8 9 10 Next

seeing searches for Companies, Equipment, Machines, Suppliers & Information

Digital Inspection Equipment

World's Best Reflow Oven Customizable for Unique Applications
Free PCB Design Checker

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
pcb assembly supplies

Inspection mirrors for electronic rework and repair.
PCB separator

MSD storage in desiccant dry canbinets