Advanced contract electronics manufacturing services of printed circuit board and circuit card assemblies for high reliability aerospace and defense applications where operation and continued performance is critical.
Water-based Cleaning Medium for Reflow and Wave Solder Equipment. Based on the MPC® Technology, VIGON® RC 101 was specifically developed to remove all types of baked-on flux residues from reflow and wave solder equipment. It reliably removes re-cond
The Malcom TK-1 Tackiness Tester is widely used to help our customers predict solder paste tack time, limiting the potential for dropped components, using either the IPC, Depth Method, or JIS Standard Test. These three convenient testing methods for
Electronics Forum | Sun Sep 30 00:54:06 EDT 2001 | chinaman
Has anybody heard about solder wires for rework with a V-notch in order to avoid solder balls which might be caused by shooting flux when getting hot. The notch is as deep to reach the core so that the flux can expand easily. I can imagine the effect
Electronics Forum | Thu Feb 07 05:24:16 EST 2008 | muarty
I would advise that you clean the stencil thoroughly at least every 4 hours, also though it is worth cleaning the stencil top and bottom after any breaktimes. To avoid solder paste drying off in stencil apertures. Best piece of kit I've purchased was
Product Details of 3D SPI-6500 Thick Paste Measurement Instrument Product Functions 1, friendly programming interface 2, a variety of measurement methods 3, scan spacing adjustable 4, image 3D simulation function 5, independent 3D dynamic obser
this type can be added with nitrogen protection system 1 Flux spraying system 1.1 Spray fluxer can sense the board size automatically, and the spraying area can be adjusted according to the width of PCB. 1.2 Spray fluxer can sense the conveyor
Industry News | 2013-03-19 13:24:40.0
Perfect inspection results with combined 2D/3D technology
Industry News | 2018-03-29 20:44:44.0
ZESTRON is pleased to announce that it will present at the Soldering, Cleaning and Coating Workshop with Arbell, Alpha Assembly Solutions, Aqueous Technologies, and MG Chemicals. This free, collaborative workshop will be held on Tuesday, April 17th in Vancouver, Canada.
Solder paste Mixer Features: Unique contoured shape, generous appearance and practical, which is made by advanced coating process workmanship. Mixing principle is on the basis of Motor rotation and revolution mode of agitation, no need to defrost
Titanium solder pot liner for a Vectra 450F solder pot. Converting your wave solder to Pb Free? Use a titanium solder pot liner to avoid the costly tin flush and risk of contamination. FOB: Origiin Contact: Assured Technical Service LLC AssuredT
Technical Library | 2008-10-15 20:16:12.0
Solder paste dispensing is usually considered a slow process. Due to the speed advantages, screen printing is used to apply solder paste whenever possible. However, screen printing is not always an option. Leveraging the high speed of piezo drive technology opens the door to a broad range of solder paste dispensing applications. The ability to dispense dots under 300-μm diameter, even as small as 125 μm, enables BGA rework, small geometry deposits for miniaturized passive components, electrical connections in recessed cavities, and RF shield attach for handheld devices.
Technical Library | 2009-09-18 14:42:37.0
In recent years, various studies have been issued on cleaning under low standoff components; most however, with incomplete information. It is essential to revisit and describe the latest challenges in the market, identifying obvious gaps in available information. Such information is crucial for potential and existing users to fully address the cleanliness levels under their respective components. With the emergence of lead-free soldering and even smaller components, new challenges have arisen including cleaning in gaps of less than 1-mil.
http://www.gpd-global.com Pair Time Pressure with Real Time Process Control (Fluid Pressure Control) to dispense Solder Mask WSOL with outstanding result. Watch this dispensing process on a bench top robot. More Info: http://www.gpd-global.com/co_w
Based on its MPC® Technology, VIGON® RC 101 was specifically developed to remove all types of baked-on flux residues from reflow and wave solder ovens. It reliably removes re-condensed fluxes and emissions from assemblies. It is also recommended for
Training Courses | ONLINE | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Mon Feb 09 12:00:00 EST 2015 - Mon Feb 09 12:00:00 EST 2015 | ,
PCB Printed Circuit Board Inspection & Quality Control Webinar
Events Calendar | Mon Jun 27 14:30:00 EDT 2016 - Mon Jun 27 16:00:00 EDT 2016 | , United Kingdom
Counterfeit Component Inspection Methods – How to do it?
Career Center | Theni, Tamilnadu India | Engineering
NPI Engineer: • Playing a role as NPI leader of the Telecom, Aerospace & Server Products to introduce and run to qualify the engineering build from customer. • Conducting Weekly NPI meeting with the CFT team to review the progress of the NPI schedu
Supply Chain Security: DFARS - Detection & Avoidance of Counterfeit Electronic Parts Online Version SMTnet Express, September 20, 2018, Subscribers: 31,325, Companies: 11,050, Users: 25,207 Supply Chain Security: DFARS - Detection & Avoidance
& Fill / Glob Top Encapsulation Hot Melt LED Encapsulation Solder Mask Solder Paste Surface Mount Adhesive Thermal Interface Material Trench Filling Underfill UV Curing Wafer Processing OTHER