Industry Directory | Manufacturer
The world's leading designer and manufacturer of precision dispensing systems that apply accurate, consistent amounts of the adhesives, sealants, lubricants and other assembly fluids used in virtually every manufacturing process.
Industry Directory | Manufacturer
dispensing equipment,dispensing machine,dispensing systems,dispensing robot,industrial robot liquid dispenser,glue dispenser,adhesive dispenser,barrel,syringe,dispensing tip,needle
New Equipment | Cleaning Equipment
QYSMT MOREL Electirc fixture cleaning machine SMS-5200 SMS-5200 electric fixture cleaning machine is mainly used for flux cleaning on the surface of wave soldering fixtures, and can also be used to clean reflow soldering trays, filters, wave solde
New Equipment | Coating Equipment
Customized IR Curing Oven If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. PCBA conformal coating machine, smt coating machine, selective co
Electronics Forum | Mon Sep 11 14:07:26 EDT 2000 | Steve
Hi ya'll!! We've got some PCB's in receiving inspection that has these little nodules in plating inside all of the barrels. These are microwave PCB's and have almost all of the surface area on both sides covered with with solid metal planes, and no
Electronics Forum | Wed Aug 21 17:03:13 EDT 2013 | hegemon
I think your pre-heat temp is a little low for SAC 305 Soldering. Especially with a Pallet. You might want to try to add some time and temp to get the PWB itself preheated up to 150-160C. That should help with the barrel fill. Make sure your board
Industry News | 2018-03-13 18:51:40.0
SMTA is excited to announce the technical program has been finalized and registration is now open for the South East Asia Technical Conference on Electronics Assembly. The event will be held May 8-10, 2018 at the MITEC in Kuala Lumpur, Malaysia.
Industry News | 2010-09-30 00:35:51.0
The new E revisions of IPC’s popular desk reference manuals, IPC-DRM-PTH, Through-Hole Solder Joint Evaluation Training & Reference Guide and IPC-DRM-SMT, Surface Mount Solder Joint Evaluation Training & Reference Guide have been released.
Parts & Supplies | Pick and Place/Feeders
101004 TRANSISTOR BC108 NPN 101020 POWER SUPPLY – UPRATED CURRENT 101047 SQUEEGEE MATERIAL 9.5 X 9.5 85-90 101081 CONNECTOR CIRCULAR 14WAY 97-3102A 101142 FRONT SQUEEGEE CARRIAGE 101143 OUTER MTG SQUEEGEE BLOCK 101145 COVER (TXT) 101146
Parts & Supplies | Pick and Place/Feeders
101004 TRANSISTOR BC108 NPN 101020 POWER SUPPLY – UPRATED CURRENT 101047 SQUEEGEE MATERIAL 9.5 X 9.5 85-90 101081 CONNECTOR CIRCULAR 14WAY 97-3102A 101142 FRONT SQUEEGEE CARRIAGE 101143 OUTER MTG SQUEEGEE BLOCK 101145 COVER (TXT) 101146
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
Technical Library | 2019-06-21 10:39:15.0
Recently, an ACI Technologies (ACI) customer called to discuss failures that they had observed with some through-hole capacitor parts. The components were experiencing failures following vibration and accelerated stress testing. Upon receipt of the samples, ACI performed three levels of inspection and Energy Dispersive Spectroscopy (EDS) testing to investigate the root cause of the failures. These analyses enabled ACI to verify the elements comprising the solder joints and make the following recommendations in order to prevent future occurrences. The first inspection was to investigate the capacitor leads using optical microscopy, and no anomalies were found that could indicate bad parts from the vendor or improper handling prior to assembly. However, vertical fill in the barrel of the plated through-holes was too close to the IPC-A-610 minimum specification of 75% to determine a pass/fail condition, and therefore required further investigation.
High-efficiency UV Curing Oven Machine If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. PCBA conformal coating machine, smt coating machine,
High Performance UV Curing Oven Machine If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. PCBA conformal coating machine, smt coating machine
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Training Courses | | | IPC-7711/7721 Specialist (CIS)
The Certified IPC-7711/7721 Specialist (CIS) training focuses on rework of electronic assemblies and repair and modification of printed boards and electronic assemblies.
SMTnet Express, December 23, 2015, Subscribers: 23,927, Members: Companies: 14,845, Users: 39,621 PCB Fabrication Processes and Their Effects on Fine Copper Barrel Cracks Edward Arthur, Charles Busa, Melissa Durfee, Chad Gibson, Wade Goldman P
| https://www.eptac.com/ask/75-barrel-fill-requirement-for-class-2-change-in-j-std-001-revision-f/
75% Barrel Fill Requirement for Class 2 Change in J-STD-001 Revision F - EPTAC - Train. Work Smarter. Succeed Looking for solder training standards, manuals, kits, and more
Surface Mount Technology Association (SMTA) | https://www.smta.org/southeast-asia/
. Understanding Parameters Affecting Barrel Fill in Wave Soldering Process Wednesday, August 15 AF Ng, Consultant, Techment Consultancy Sdn Bhd Conventional Wave Soldering has been employed for soldering of boards since long time ago