KS-635 Lead-free Fully Computer-controlled Reflow Oven Model KS-635 Heating part parameter Number of heating zones Up 6 down 6 Length of heating zone 2100mm Heating method Hot Air
New Equipment | Industrial Automation
face mask making machine For disposable nonwoven face mask body making.Every minute can output 80-100 pieces of mask body. Normally work together with face mask earloop welding machine, face mask tie on machine, from non woven raw material to co
Electronics Forum | Mon Aug 31 11:52:28 EDT 2020 | inspiredmorris20
Hello Jon, I appreciate your reply, correct there are 2 red (24v) that control the main power and 2 blue (they control the power to the units operation keys ready, start, stop, reset, change feeders.) additionally there is a red jumper wire on the E
Electronics Forum | Fri Aug 28 17:47:59 EDT 2020 | inspiredmorris20
thanks Stephen!! I'm testing for voltage and have found 24v going through the E-stop to the main switch. If i trip the E-stop i can disengage the main switch. I have no more control to the hardware then that. The software is not throwing any code ot
Used SMT Equipment | Board Cleaners
• Vintage 2008 • PLC based Control System • 480V AC 60Hz • Auto Stop/Stand by Mode • Final Rinse low flow sensor and alarm • Mach II Drying System • 2 upper, 2 lower jet manifolds • 15 HP blower upgrade • 18” Off Load Extension • Integrated
Used SMT Equipment | Labeling Systems
CTI Systems In-Line Laser Marker Model: A-MS2-10W/C02-2-1M-3387 Vintage: 2014 10 Watt C02 Synrad Laser Fume Extractor 1.0Meter wide footprint with 16″ W x 18″L PCB capability Fiducial correction and live teach/view camera. Secondar
Industry News | 2020-12-20 23:40:23.0
Easily Installed Excel Cell Emergency Switches Available in 22mm, O25mm and O30mm Mounting Diameters
Industry News | 2020-12-21 09:13:06.0
Easily Installed Excel Cell Emergency Switches Available in 22mm, O25mm and O30mm Mounting Diameters
Parts & Supplies | Pick and Place/Feeders
JUKI 2050 machine failure solution KE2050M Z-axis fault E620014 error handling method! Suddenly heard the sound of the machine. The machine stopped the fault for the E620014Z axis drive alarm. View the drive. For Z drive 1, the third light is on
_1.jpg)
Parts & Supplies | Pick and Place/Feeders
472248403 SPRING RETAINER SPRING BEARING SI E1100 4-722-484-03 AF1305RF1 BF6040L BF4020G BF4025G BF0090L BF2520L BFRE020 BFRE04L BFRE060 BFRE070 BF6020G BFRE02G AF06021F1
Technical Library | 2019-12-12 02:43:44.0
Today we discuss the reason that causes temperature humidity chamber to alarm,In most cases, the equipment alarm is caused by the improper operation in the process of use, which mainly includes following reasons:that are refrigeration system, temperature system and circulating system. First, Refrigeration system 1, refrigeration compressor overpressure alarm. If the refrigerant pressure exceeds the set value, it will stop and alarm at the same time. At this time, the fault must be eliminated and then manually reset. 2, short phase power supply, phase sequence alarm. When the external power supply of the equipment is out of phase or the phase sequence is changed, it will stop and alarm at the same time. 3. The circulating cooling water is short of water to alarm. When the water pressure of the cooling circulating water system is insufficient, it will stop and alarm at the same time, and it must wait for the fault to be eliminated and reset at the same time before it could run normally. 4, refrigeration compressor overheating alarm. When the coil of the compressor is overheated and the power supply of the line is not normal, it will stop and alarm at the same time. Second, Temperature system 1, the overtemperature alarm in the chamber. The sensors in the channel and the sample area are equipped with overtemperature protection devices, and there are also overtemperature protecter on the control panel. When the temperature in the working chamber exceeds the setting value on the controller, it will stop and alarm. 2. sample overtemperature protection. When the temperature in the sample area exceeds the protection temperature set by the controller, it will stop and alarm at the same time. The overtemperature protection of the sample is divided into upper limit protection and lower limit protection, which can be set according to the demand, Third,Circulating system 1. The alarm is caused by the overheating of the circulating fan. When the coil of the fan is over-heated, the alarm will be stopped at the same time. 2. The fan over-current alarm. When the current of the fan exceeds the allowable value, the alarm is stopped at the same time, and the normal operation can only be carried out after the fault maintenance of the overcurrent is completed. This is what we talk about today,if you have more questions,let us know.
Link: https://www.ascen.ltd/Products/mask_making_machine/ disposable medical face mask manufacturing machine also known as face mask production line,dusk mask machine,disposable face mask making machine.It is automatic output,a face mask body machine
Link: https://www.ascen.ltd/Products/mask_making_machine/ This kind of medical face mask manufacturing machine non woven dust mask machine is the auto equipment which be used to the product of disposable face masks, be suitable for the material of no
Career Center | 10th of ramadan, Egypt | Engineering,Maintenance,Management,Production
• Excellent Analytical, inter-personal and communication skills • Ability to work effectively in teamwork • Ability to set and achieve goals and work under pressure • Learn quickly, hard worker • Capable of study and research acti
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/FLOwareGEMInterface_1.2.0.pdf
3.3.6 Related Variables, Constants and Events ..............................................................................19 3.4 ALARMS .........................................................................................................................................19 3.4.1 General Description
