Technical Library | 2023-01-17 17:19:44.0
A test program was developed to evaluate the effectiveness of vacuum reflow processing on solder joint voiding and subsequent thermal cycling performance. Area array package test vehicles were assembled using conventional reflow processing and a solder paste that generated substantial void content in the solder joints. Half of the population of test vehicles then were re-processed (reflowed) using vacuum reflow. Transmission x-ray inspection showed a significant reduction in solder voiding after vacuum processing. The solder attachment reliability of the conventional and vacuum reflowed test vehicles was characterized and compared using two different accelerated thermal cycling profiles. The thermal cycling results are discussed in terms of the general impact of voiding on solder thermal fatigue reliability, results from the open literature, and the evolving industry standards for solder voiding. Recommendations are made for further work based on other void reduction methods and additional reliability studies.
Technical Library | 2023-01-17 17:22:28.0
The impact of voiding on the solder joint integrity of ball grid arrays (BGAs)/chip scale packages (CSPs) can be a topic of lengthy and energetic discussion. Detailed industry investigations have shown that voids have little effect on solder joint integrity unless they fall into specific location/geometry configurations. These investigations have focused on thermal cycle testing at 0°C-100°C, which is typically used to evaluate commercial electronic products. This paper documents an investigation to determine the impact of voids in BGA and CSP components using thermal cycle testing (-55°C to +125°C) in accordance with the IPC- 9701 specification for tin/lead solder alloys. This temperature range is more typical of military and other high performance product use environments. A proposed BGA void requirement revision for the IPC-JSTD-001 specification will be extracted from the results analysis.
Technical Library | 2023-09-07 14:38:31.0
A repeat customer specializing in high-technology interconnect, sensor, and antenna solutions, partnered with us to dispense small volumes of solder paste (Indium 10.1 SAC305 T6SG 78%m) onto backplane connectors – gold pads 0.175mm x 0.225mm. We performed a test requiring 0.200mm diameter or smaller dots to demonstrate the dispensing capability required.
Technical Library | 2020-12-02 20:36:54.0
Industry 4.0 is a topic of much discussion within the electronics manufacturing industry. Manufacturers and vendors are trying to come to terms with what that means. In the most simplistic of terms, Industry 4.0 is a trend toward automation and data exchange within the manufacturing process. This basically requires connectivity and communication from machine to machine within the manufacturing line. The challenge is to collect data from each of the systems within the line and make that data available to the rest of the machines. Without test and inspection, there is no Industry 4.0. The whole purpose of test and inspection is to collect actionable data that may be used to reduce defects and maximize efficiency within the manufacturing line. The goal is to minimize scrap and get a really good handle on those process parameters that need to be put in place to manufacture products the right way the first time. For maximum efficiency, three inspection systems are required within the production line. These are solder paste inspection (SPI) post-solder deposition, automated optical inspection (AOI) post-placement, and AOI post-reflow. This requires a substantial investment; however, the combination of all three inspection machines is really the only true way to provide feedback for each stage of the manufacturing process.
Technical Library | 2020-02-03 17:37:36.0
Accurate impact testing is a key component to establishing that a product is not only reliable, but durable in an end-use environment. ACI Technologies tested a high-g circuit board to demonstrate component durability and ruggedization for guided munitions. The Lansmont Model 23 Shock Test System customized with a Dual Mass Shock Amplifier was used for this testing (Figure 1).
Technical Library | 2019-05-31 14:19:24.0
ACI Technologies (ACI) characterized the reliability of surface mount RF components. The RF frequency band of interest was the X band (10.7 to 11.7GHz). A two pronged test for reliability of circuit card assemblies (CCA) was designed for both extreme thermal cycling and vibration. The rapid thermal cycling and extreme vibration testing simulates the total stress encountered by the assembly over the life of the product but accomplishes it in a relatively short period of time. In order to perform the reliability testing, a test vehicle consisting of a printed circuit board with test structures and components, was designed, fabricated, and assembled at ACI.
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
Technical Library | 2019-05-29 10:40:59.0
Design for Test or Design for Testability (DFT) can best be described as the techniques utilized to add testability features to an electronic hardware product design. These added features make it easier to develop and apply manufacturing tests to assure that the product functions correctly.
Technical Library | 2019-09-23 09:35:00.0
Failure analysis (FA), by its very nature, is needed only when things goawry. Before any testing is performed on the sample, a decision mustbe made as to whether or not the sample is allowed to be destroyedin the process of testing. Non-destructive testing can allow for re-use of the assembly since the functionality is not altered, but there still remains the possibility that inadvertent damage can occur through the course of the analysis. If non-destructive testing is preferred, then the following types of analysis can be performed. The testing can be divided into four categories: visual, X-ray (X-ray imaging and X-ray fluorescence), cleanliness (resistivity of solvent extract, ion chromatography, and Fourier transform infrared spectroscopy), and mechanical (non-destructive wire bond pull).
Technical Library | 2023-11-14 02:36:41.0
Understanding In-Circuit Testing (ICT) with PCBA ICT Testing Machine In-Circuit Testing, commonly known as ICT, stands as a sophisticated and precise method within electronics manufacturing. It serves to evaluate the functionality and integrity of individual electronic components on a Printed Circuit Board (PCB). The process employs specialized equipment called ICT Testers, meticulously designed to pinpoint defects, shorts, opens, and other potential issues within the PCB assembly. The Crucial Role of PCBA ICT Testing Machine 1. Quality Assurance ICT is pivotal in ensuring the overall quality and reliability of electronic products. Early identification and rectification of defects in the production process help manufacturers avoid costly recalls, rework, and post-production issues. 2. Cost-Efficiency ICT significantly reduces manufacturing costs by identifying defects at an early stage. This results in fewer defective units reaching the end of the production line, minimizing waste and rework. 3. Faster Time-to-Market Manufacturers can expedite the production process with ICT by swiftly identifying and resolving issues. This leads to faster product launches, providing a competitive edge in the market. Unveiling the Functions of PCBA ICT Testing Machine The ICT Tester, the core of the In-Circuit Testing process, conducts a battery of tests on each PCB, including: 1. Continuity Testing Checks for open circuits, ensuring all connections are properly established. 2. Component Verification Verifies the presence and orientation of components, ensuring alignment with the PCB design. 3. Functional Testing Some ICT Testers execute functional tests, assessing electronic components' performance as per specifications. 4. Short Testing Identifies unintended connections or shorts between different components on the PCB. 5. Insulation Testing Checks for isolation between different circuits, ensuring no undesired connections or paths. 6. Programming and Configuration In some cases, ICT Testers are used to program and configure specific components on the PCB. Advantages of PCBA ICT Testing Machine 1. High Precision ICT offers unparalleled accuracy in defect detection, making it crucial in modern electronics manufacturing. 2. Speed and Efficiency ICT Testers enable rapid testing, allowing manufacturers to assess a large number of PCBs in a short time. 3. Customization ICT Tests can be tailored to suit specific PCB requirements, ensuring thorough evaluation of every design aspect. 4. Data Collection ICT Testers gather valuable data for process optimization and quality control. In-Circuit Testing (ICT) is fundamental in electronics manufacturing, safeguarding product quality, reducing costs, and accelerating time-to-market. The ICT Tester, with its precision and efficiency, positions manufacturers at the forefront of the highly competitive electronics industry. Embracing ICT is not just a choice; it's a necessity for manufacturers striving for excellence in their products. I.C.T is a leading manufacturer of full SMT line machines in the electronic manufacturing industry. Discover how we can enhance product quality, boost performance, and reduce costs. Contact us at info@smt11.com for reliable global supply, unparalleled efficiency, and superior technical service.
