Industry Directory | Consultant / Service Provider
Design and manufacture of thermal systems for rapid temperature verification and testing, and process cooling. Includes small-footprint thermal chambers and plates, mobile temperature forcing systems, and process chillers.
Industry Directory | Manufacturer
ASLi main products: Temperature (humidity) chamber, Thermal Shock Test Chamber, Sand and Dust Tester , Rain Spray Tester, UV Chamber, Ozone Chamber, Xenon Climate Chamber , Salt Spray Corrosion Chamber, High Temperature (Vacuum )
Dual Chamber Module - Dual Chambers + Dual Blowers + Dual Heaters + Dual T/Cs. Bifurcated (Dual) chamber reflow oven allows 2 different thermal profiles to run simultaneously in the same reflow oven foot print Improved temperature uniformity acro
The OmniMax reflow soldering system is designed to deliver maximum thermal performance combined with process capability and control. IsoThermal™ Chamber Technology The OmniMax reflow soldering system is designed to deliver maximum thermal per
Electronics Forum | Tue Mar 09 11:10:31 EST 2010 | baildl632
Graceyt, I know you are being shot a lot of info. Have you gotten any resolution to this problem? I've seen similar problems in our thermal chamber with Demodulation units. The IC, in the module, inside the radio inside the chamber at the top of ou
Electronics Forum | Thu Feb 16 02:03:36 EST 2017 | soldertraining
Reflow ovens and wave solder machines come in a huge variety of flavors and price points. These machines tell the story of impressive features and capabilities such as flux management, gas flow management, static pressure control, active cooling zone
Used SMT Equipment | General Purpose Equipment
Tenney - Blue M Thermal Shock Chamber For Sale See attached pictures and information below Equipment Information Tenney - Blue M - TPS Model Number: WSP-109 Serial Number: 0801000082 Year: 2007 Type: Hot Cold - Shock
Used SMT Equipment | General Purpose Test & Measurement
Very Nice Thermotron Thermal Shock Chamber For Sale See attached pictures and information below Thermotron Model Number: ATS-320-V-10-705 Serial Number: 44470 Year: 2013 Type: Shock Chamber - Hot/Cold -73 to 177C Hot Zone 60 to 200C 8800
Industry News | 2024-03-11 15:00:03.0
Connect with our experts and see plasma and dispensing equipment for microelectronics manufacturing in booth 3645
Industry News | 2018-10-18 08:42:00.0
Reflow oven zone temperature set up and thermal profile
.jpg)
Parts & Supplies | Soldering - Reflow
This reflow oven is top quality oven represent the world's best low cost, high performance solder reflow sytem. The sensor is designed in the front of tip and the temperature induction is very exact and sensitive, the speed of heating and recovery of
Technical Library | 2007-01-31 15:17:04.0
The goal of this project is to evaluate the reliability of lead-free BGA solder joints with a variety of different pad sizes using several different BGA rework methods. These methods included BGAs reworked with both flux only and solder paste attachment techniques and with or without the use of the BEST stay in place StencilQuick™. The daisy chained test boards were placed into a thermal test chamber and cycled between -25ºC to 125ºC over a 30 minute cycle with a 30 minute dwell on each end of the cycle. Each BGA on the board was wired and the continuity assessed during the 1000 cycles the test samples were in the chamber.
Technical Library | 2019-11-12 02:09:22.0
Thermal shock test chamber can be used for testing the chemical change or physical damage on composite materials caused by the thermal expansion and contraction of the sample in the shortest time,which is subjected to extremely and continuous high and low temperature environment.so how to check the temperature recovery time of this chamber? Normally we take following steps to inspect the temepratuire recovering time: 1.Install the temperature sensor at the specified position, and adjust the temperature controller of hot zone and cold zone to the required nominal temperature respectively. 2.The temperature increases and reduces respectively,30min after temperature in two zones reach stable status,record temperature value of the measuring point,pls set the temperature value of two zones to be required nominal temperature. 3.The temperature shock test chamber automatically places the inspected load into theh ot zone,select the corresponding retention time according to regulated standard. 4.Set the transfer time,then the inspection load is transferred from hot zone to cold zone, and the temperature of the measuring point is observed and recorded, and then the reverse conversion of the load from cold zone to hot zone is carried out according to the same method, and the temperature of the measuring point is observed and recorded. www.climatechambers.com
Events Calendar | Wed Apr 19 00:00:00 EDT 2017 - Fri Apr 21 00:00:00 EDT 2017 | Nara, Japan
Ceramic Interconnect and Ceramic Microsystems Technologies (CICMT 2017)
International Microelectronics Assembly and Packaging Society (IMAPS)
Career Center | Manhattan, Kansas USA | Production
Ultra Electronics, ICE is a leader in small aircraft aerospace systems and components. ICE secured its first contract in the aircraft industry in 1975 by designing and manufacturing a state-of-the-art deicer timer for Cessna Aircraft Company. ICE c
Career Center | kerala, any ware India | Production
i have experience in • Operation of wave soldering and water cleaning machine • Inspection ( Reflow and Post Wave ) • Pre Reflow inspection in SMD • Component forming stuffi
Career Center | Bangalore, India | Engineering,Management,Production,Quality Control,Technical Support
WORK EXPERIENCE DETAILS: 7+ Years of Experience in manufacturing & hardware testing of Protocol conveter & Commissioning, Products delivery and QA/QC. 2+ Years of Experience in Hardware testing and Package Level testing. 2+ Years of Experience in
Surface Mount Technology Association (SMTA) | https://www.smta.org/knowledge/proceedings_abstract.cfm?PROC_ID=5296
Alloy Composition and Thermal Fatigue of High Reliability Pb-Free Solder Alloys 中文 MEMBERS LOGIN Membership Become a Member! Renew Membership About SMTA Ambassadors Benefits Classifications Member Directory Member Directory Corporate Suppliers Corporate Users Consultants List Advertisers Update Your Info
Heller 公司 | http://hellerindustries.com.cn/Vacuum-Void-Reduction-Reflow.pdf
The Effect of Vacuum Reflow Processing On Solder Joint Voiding And Thermal Fatigue Reliability To be published in the Proceedings of SMTA International, September 17 - 21, 2016, Rosemont, IL
