500⁰C) Compatible with multiple lamination cycles Standard PCB lamination cycles may be used Excellent for Laser Via formation Excellent CAF resistance Uses standard desmear and plating processes High Modulus: 1100 kpsi Lo
New Equipment | Test Equipment
AutoCAF™ is able to measure up to 256 individual measurement sites under conditions of high humidity and temperature in accordance with IPC-TM-650 2.6.25 Test Method & IPC 9691 CAF Test Users Guide. Conductive anodic filament (CAF) failure is copper
Electronics Forum | Mon Nov 15 21:35:50 EST 1999 | Dave F
Bob Bob: Fortunately, you found this before you built-up a lot of product. Some thoughs and other drivel: 1 Use IPC-TM-650, Method 2.4.8 for copper peel with a Instron machine. Typical pad peel strength requirement for FR-4, 2 oz. copper is: 6 l
Electronics Forum | Wed Jun 12 08:13:29 EDT 2002 | davef
Don't sound proper. There is no specification. Pad peel strength test methods are: * IPC-TM-650, Method 2.4.21 for multiple solderings * IPC-TM-650, Method 2.4.8 for copper peel with a Instron machine. Typical requirement for Cu is: 6 lbf/in [1
Industry News | 2019-03-10 20:30:11.0
The proliferation of tighter microvia densities and signal integrity requirements in printed boards within the electronics industry has revealed reliability concerns with microvia structures in high performance products. A number of IPC OEM member companies have approached IPC with examples of microvia failures in high-profile hardware that were not observed until after bare printed board fabrication, inspection and acceptance, including:
Industry News | 2011-09-23 22:44:43.0
IPC presented Special Recognition, Distinguished Committee Leadership and Committee Service Awards at IPC Midwest Conference & Exhibition, held September 21-22, 2011, in Schaumburg, Illinois.
Technical Library | 2018-08-15 17:27:28.0
Smartphones and tablets require very high flexibility and severe bending performance ability of the flexible printed circuits (FPCs) to fit into their thinner and smaller body designs. In these FPCs, the extraordinary highly flexible, treated rolled-annealed (RA) copper foils have recently used instead of regular RA foil and electro deposited foils. It is very important to measure the Young's moduli of these foils predicting the mechanical properties of FPCs such as capabilities of fatigue endurance, folding, and so on. Even though the manufacturers use IPC TM-650 2.4.18.3 test method for measuring Young's modulus of copper foils over many years, where Young's modulus is calculated from the stress–strain (S–S) curve, it is quite difficult to obtain the accurate Young's modulus of metal foils by this test method.
Career Center | Shen Zhen, China | Management,Sales/Marketing
Working in GLORYPCB for 10 years.knowing electronic supply chain very well. especially for PCB PCBA assembly and other Electronic Manufacturing Service.Glorypcb is a professional electronic manufacturer located in Shenzhen with three facilities.offe
SMTnet Express, August 16, 2018, Subscribers: 31,259, Companies: 11,015, Users: 25,092 Reliable Young's Modulus Value of High Flexible, Treated Rolled Copper Foils Measured by Resonance Method Kazuki Kammuri, Atsushi Miki, Hiroki Takeuchi; JX
SMTnet Express, July 13, 2017, Subscribers: 30,584, Companies: 10,624, Users: 23,496 Divergence in Test Results Using IPC Standard SIR and Ionic Contamination Measurements K. Tellefsen, M. Holtzer, T. Cucu, M. Liberatore, M. Schmidt - Alpha
| https://www.eptac.com/faqs/ask-helena-leo/ask/copper-elongation-and-tensile-strength-requirements
? For example, military standard MIL-PRF-31032 states copper elongation shall... Question: IPC-TM-650, 2.4.18.1 is the method for testing in-house plating for tensile strength and elongation, but where can I find the IPC requirements for results
