Technical Library | 2023-01-17 17:37:45.0
Various international market trends drive electronics manufacturers and their mate- rials and equipment suppliers to develop new assembly techniques to reduce the industry's environmental impact. Two pri- mary forces in this drive are the movements to lead-free assembly and ISO 14000 cer- tification. In response to these factors, reflow technology advances are enabling manufacturers to meet or anticipate the new environmental mandates.
Technical Library | 2023-01-17 17:19:44.0
A test program was developed to evaluate the effectiveness of vacuum reflow processing on solder joint voiding and subsequent thermal cycling performance. Area array package test vehicles were assembled using conventional reflow processing and a solder paste that generated substantial void content in the solder joints. Half of the population of test vehicles then were re-processed (reflowed) using vacuum reflow. Transmission x-ray inspection showed a significant reduction in solder voiding after vacuum processing. The solder attachment reliability of the conventional and vacuum reflowed test vehicles was characterized and compared using two different accelerated thermal cycling profiles. The thermal cycling results are discussed in terms of the general impact of voiding on solder thermal fatigue reliability, results from the open literature, and the evolving industry standards for solder voiding. Recommendations are made for further work based on other void reduction methods and additional reliability studies.
Technical Library | 2023-01-17 17:12:33.0
Reflowed indium metal has for decades been the standard for solder thermal interface materials (solder TIMs or sTIMs) in most high-performance computing (HPC) TIM1 applications. The IEEE Heterogeneous Integration Thermal roadmap states that new thermal interface materials solutions must provide a path to the successful application of increased total-package die areas up to 100cm2. While GPU architectures are relatively isothermal during usage, CPU hotspots in complex heterogeneously-integrated modules will need to be able to handle heat flux hotspots up to 1000W/cm2 within the next two years. Indium and its alloys are used as reflowed solder thermal interface materials in both CPU and GPU "die to lid/heat spreader" (TIM1) applications. Their high bulk thermal conductivity and proven long-term reliability suit them well for extreme thermomechanical stresses. Voiding is the most important failure mode and has been studied by x-ray. The effects of surface pretreatment, pressure during reflow, solder flux type/fluxless processing, and preform design parameters, such as alloy type, are also examined. The paper includes data on both vacuum and pressure (autoclave) reflow of sTIMs, which is becoming necessary to meet upcoming requirements for ultralow voiding in some instances.
Technical Library | 2023-09-07 14:54:10.0
A global manufacturer of a broad line of electronic interconnect solutions worked with us to dispense conductive adhesive EpoTek H20E-FC. EpoTek H20E-FC is a two-component, electrically conductive, snap curing epoxy for photovoltaic thin film module stringing, semiconductor packaging and PCB circuit assembly. The primary goal was filling a rectangular cavity on a connector. The epoxy needed to fill the connector to the top of the walls in less than three seconds.
Technical Library | 2009-04-23 08:14:37.0
No SMT equipment can place accurately and run efficiently without quality nozzles and feeders. These two factors are the core of the pick and place process. If the machine is either unable to pick parts consistently or hold on to the components during the transport from feeder to PCB, defects will result.
Technical Library | 2019-06-20 07:45:19.0
One of the two basic risks of employing the commercially accepted, Restriction of Hazardous Substances (RoHS) compliant, lead-free (Pb-free) electronics is the threat to the electronics reliability from the growth of tin whiskers. The other basic risk deals with Pb-free solder joint reliability.
Technical Library | 2018-04-27 12:59:29.0
Hot Air and IR are the two main types of rework stations used by OEMs and PCB contract manufacturers today. Both have advantages and disadvantages and choosing the right one for your application requires a careful consideration of a number of factors, including your budget, your working requirements and the capabilities of your staff. In this article, we outline some of the differences between hot air and IR BGA rework stations.
Technical Library | 2019-10-07 10:56:06.0
Power interfaces are required when external power sources like solar panels, fuel cells, or batteries are used to generate power for electrical devices. There are two major power interfaces commonly used, direct current to direct current (DC/DC) converters and direct current to alternating current (DC/AC) inverters. While both interfaces are designed to convert from variable DC inputs, they output to different power standards and power levels that are used in different applications.
Technical Library | 2019-05-31 14:19:24.0
ACI Technologies (ACI) characterized the reliability of surface mount RF components. The RF frequency band of interest was the X band (10.7 to 11.7GHz). A two pronged test for reliability of circuit card assemblies (CCA) was designed for both extreme thermal cycling and vibration. The rapid thermal cycling and extreme vibration testing simulates the total stress encountered by the assembly over the life of the product but accomplishes it in a relatively short period of time. In order to perform the reliability testing, a test vehicle consisting of a printed circuit board with test structures and components, was designed, fabricated, and assembled at ACI.
Technical Library | 2019-10-16 10:20:25.0
A major goal of the development of advanced packaging technology is to reduce the size, weight, and power consumption of electronics components using state-of-the-art commercial technologies. One of the novel concepts involves the use of all three spatial dimensions when designing and producing new systems. In the past, electronic structures tended to be two dimensional in nature. Generally speaking, individually packaged integrated circuit (IC) dies were interconnected on printed circuit boards. Techniques such as die and package stacking naturally contribute to a reduction of the spatial footprint of any given electronic system design.
