New SMT Equipment: use of 2kv capacitors (5)

HeatShieldGel™ - Thermal Protection of Electronic Components During Reflow

HeatShieldGel™ - Thermal Protection of Electronic Components During Reflow

New Equipment | Rework & Repair Equipment

BEST HeatShield Gel™ is a thermal shield water-based gel designed to be used in the PCB rework/repair or board assembly areas in order to provide thermal protection of electronic components. It is truly a revolutionary means to protect components. It

BEST Inc.

200W computer digital control of portable high voltage power supply

200W computer digital control of portable high voltage power supply

New Equipment |  

【Type】 DEC 【Power(W)】 60W-200W 【Maximum output voltage(kV)】 ,0.5,0.8,1,2,3,5,8,10,15,20,30,40,50,60,65,70,80,100, Wisman DEC series high voltage power supply is a portable high voltage power supply, computer digital control and analog control opt

Wisman High Voltage Power Supply Co.,LTD.

Electronics Forum: use of 2kv capacitors (30)

Reflow of 0402 capacitors

Electronics Forum | Thu Mar 08 16:02:58 EST 2001 | arturoflores

You did not mention to change the solder paste to another formulation or brand.We used to have that kind of non wetting problem on 0402 cap when we used Alpha's LR737(63/37) Type 4 No Clean and the solution was to change the solder paste to Alpha's L

Reflow of 0402 capacitors

Electronics Forum | Thu Mar 08 22:24:45 EST 2001 | davef

Sounds like you've done a good job of troubleshooting. Two thoughts are: 1 An alternative to using a hotter flux that the others mentioned is to use components with more solderable terminations. [A firm grasp on the obvious.] 2 You spoke about

Industry News: use of 2kv capacitors (25)

Updates in IPC-6018B Help Engineers Design High-reliability Boards Specification addresses growing field of microwave technology

Industry News | 2012-05-04 09:21:15.0

As printed boards evolve and chip speeds increase, the use of microwave technology in commercial applications, such as cell phone towers and in military products, is expanding.

Association Connecting Electronics Industries (IPC)

BEST Developes Revolutionary Gel for Masking of Parts

Industry News | 2016-01-05 16:10:10.0

Novel method for protecting electronic components from heat.

BEST Inc.

Parts & Supplies: use of 2kv capacitors (1)

Yamaha KSUN SMT Original Used head of Z axis  servo  card

Yamaha KSUN SMT Original Used head of Z axis servo card

Parts & Supplies | Assembly Accessories

YAMAHA KSUN SMT Original Used KHY-M5802-02  head of Z axis  servo  card More Yamaha parts in stock KM9-M7107-00XSHFT, HEAD ASSYYV100II     KM9-M7106-00XSHAFT HEAD ASSY YV100II     KV8-M713S-A0X STD.SHAFT2,SPARE YV100X    KV8-M712S-A0X STD.SHAFT

Dongguan Kingsun Technology Co.,Ltd.

Technical Library: use of 2kv capacitors (3)

Investigation of Through-Hole Capacitor Parts Failures Following Vibration and Stress Testing

Technical Library | 2019-06-21 10:39:15.0

Recently, an ACI Technologies (ACI) customer called to discuss failures that they had observed with some through-hole capacitor parts. The components were experiencing failures following vibration and accelerated stress testing. Upon receipt of the samples, ACI performed three levels of inspection and Energy Dispersive Spectroscopy (EDS) testing to investigate the root cause of the failures. These analyses enabled ACI to verify the elements comprising the solder joints and make the following recommendations in order to prevent future occurrences. The first inspection was to investigate the capacitor leads using optical microscopy, and no anomalies were found that could indicate bad parts from the vendor or improper handling prior to assembly. However, vertical fill in the barrel of the plated through-holes was too close to the IPC-A-610 minimum specification of 75% to determine a pass/fail condition, and therefore required further investigation.

ACI Technologies, Inc.

Soldering of SMD Film Capacitors in Practical Lead Free Processes

Technical Library | 2009-06-02 23:53:18.0

Today the lead free soldering process is a must in commercial electronics and it is also coming more and more important in automative and industrial electronics sectors in the near future. The most common choices for lead free solders are different Tin-Solder-Copper (SAC) alloys. Processes using SAC solders cause extra stress, because of increased process temperatures, especially to the plastic materials.

KEMET Electronics Corporation

Express Newsletter: use of 2kv capacitors (903)

Hermetically Sealed SMD Tantalum Capacitors

Hermetically Sealed SMD Tantalum Capacitors Hermetically Sealed SMD Tantalum Capacitors by: I.Zednickova, M.Biler, J.Petrzilek, T.Zednicek; AVX Corporation The article presents improvement of stability parameters of tantalum surface mounted

SMTnet Express - January 22, 2015

SMTnet Express, January 22, 2015, Subscribers: 22,251, Members: Companies: 14,183, Users: 37,571 High Temperature Ceramic Capacitors for Deep Well Applications. R. Phillips, J. Bultitude, A. Gurav, K. Park, S. Murillo, P. Flores, M. Laps - KEMET

Partner Websites: use of 2kv capacitors (268)

Calendar of Events

Surface Mount Technology Association (SMTA) | https://www.smta.org/news/smta_calendar/calendar.cfm

hot air guns for feed through capacitors, wire wrap back planes, heat shields and cable forms. Welcome to the interesting and creative world of solder preforms Our first preform webinar includes

Surface Mount Technology Association (SMTA)

What are the functions of the process equipment of Semi-auto SMT Production Line?

| https://www.smtfactory.com/What-are-the-functions-of-the-process-equipment-of-Semi-auto-SMT-Production-Line-id3048478.html

. If the SMD components on the PCB are only resistors, capacitors, and the package is 1206 or more, you do not need to make a template, and use a syringe or automatic dispensing equipment


use of 2kv capacitors searches for Companies, Equipment, Machines, Suppliers & Information

Sm t t t t t t t t t t net
  1 2 3 4 5 6 7 8 9 10 Next