Industry Directory | Consultant / Service Provider
NJ Duct Cleaning has years of experience in providing quality duct cleaning service. Contact us now if you are looking for cleaning service in NJ.
Industry Directory | Manufacturer
Lets face it, some areas of house like are just impossible to clean, that is why you need an expert help. Call No1Cleaners right now and get help with mold cleaning service in NJ.
The GTS humidifier LX Series is the only gas-fired humidifier that combines the highest efficiency on the market with ultra-low NOx in a single design. Thermal (combustion) efficiency 94% Higher Heating Value (HHV) of fuel 103% Lower Heating Value
Flux application using the DispenseJet® pump is a superior alternative to screen printing and ultrasonic spray. Jet dispensing eliminates the overspray and material waste associated with ultrasonic and spray application methods. Flux application usi
Electronics Forum | Wed Aug 14 10:11:01 EDT 2002 | davef
For relow ovens the general approaches are: * Clean the vent pipe. * Replace [a section of ] the vent pipe. * Clean the flux trap on newer ovens. * Do nothing and wonder where that brown slime that is dripping on the boards is coming from. For wave
Electronics Forum | Wed Jan 20 14:28:50 EST 1999 | Dave F
| I have a severe problem with flux residue being drawn up the vent ducts of my reflow oven. This residue reaches a critical mass then begins to flow down the ducts and becomes very messy. I run a no-clean process and use IR oven. Has anyone else o
Used SMT Equipment | Coating and Encapsulation
Details: • Solvent-purge station with cups • Door Interlock controls • Light beacon • Downdraft ventilation with redundant safety vent switch • Stainless steel interior • Front access hatch with glass • In-line standard chain conveyor Conditi
Used SMT Equipment | Soldering - Reflow
Novastar GF12 Reflow Oven Equipment Description Novastar Model Number: GF-12HC/HT Serial Number: 1101232 Year 2011 Max Board Width: 12" Max Temperatute: 350C or 622F Heated Tunnel Length: 26" 3 Zones top, 3 Zones bottom Venting: 4" fla
Industry News | 2010-10-11 14:57:11.0
Industry-leading associations IPC and SMTA jointly announce the agenda for Session 4 of the High Performance Cleaning and Coating Conference, scheduled to take place November 16-18, 2010 at the Renaissance Hotel & Convention Center in Schaumburg, Illinois.
Industry News | 2020-08-07 07:29:43.0
The SMTA Capital Chapter is excited to host its first FREE webinar on Wednesday, August 19th. The webinar will include an informative presentation given by industry expert Norman Armendariz, Ph.D. of Raytheon Company on "DfR- Design for Rinse-ability: Effect of SMT Component Package Design on Cleaning Effectiveness."
Parts & Supplies | Pick and Place/Feeders
AXIAL AIR VENT 4414F 24VDC
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
Technical Library | 2021-12-06 03:43:31.0
By potting under vacuum, components can be optimally protected from external influences. Before the potting process, air and moisture are removed from the components by vacuum. Components with geometries that are difficult to vent, coils, transformers or wound goods can be potting free of air bubbles. Potting under vacuum guarantees an even distribution of the potting material.Whatsapp 0086 134 2516 4065
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
RCM-H1000D series Desktop automatic centrifugal mixer-temperature recovery type One.piece use clause H1000D desktop automatic centrifugal mixer is based on current technology and safety standards: GB4793.1-2007 "Safety requirements for electrical eq
Events Calendar | Wed Aug 19 00:00:00 EDT 2020 - Wed Aug 19 00:00:00 EDT 2020 | ,
DfR - Design for Rinse-Ability: Effect of SMT Component Package Design on Cleaning Effectiveness
| https://pcbasupplies.com/smt-equipment-universal-instruments-flexjet-07-09-7-spindle-head/
[47561117] $ 65.00 Add to cart Universal Instruments 08 MPF Ceramic [47561106] $ 65.00 Add to cart Universal Instruments 08 MPFX Vented Ceramic [47561112
| http://www.thebranfordgroup.com/dnn3/
[Available for Immediate Sale] 4.5" Diamond America Extruder, 32:1 L/D Ratio, Water Cooled Barrel, Vented - 4.5" NRM Extruder [Available for Immediate Sale] Used 4.5" NRM Extruder, 32
