Industry Directory | Manufacturer
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
Industry Directory | Manufacturer
One-Stop Solution for PCB & Prototype Assembly Expanded PCB manufacturing capabilities to support advanced designs with demanding requirements including laser-drilled microvias, cavity boards, heavy copper up to 20 oz., via-in-pad
PCB depaneling often happen right after SMT processing or after soldering,or after in-circuit test in the assembly line.PCB depaneling machine to be a important equipment in high-volume electronics assembly production. To choose the ASCEN PCB de
New Equipment | Selective Soldering
To see more visit Pillarhouse here: https://www.pillarhouse.co.uk/products/selective-soldering-handload/pilot-handload Economical, compact, single point selective soldering system The all-new ultra-low-cost Pilot machine has been designed as an ent
Electronics Forum | Wed Feb 01 14:31:03 EST 2006 | John S.
http://www.saturnelectronics.com/docs/Getting_the_Lead_Out.pdf This is a document provided by one of our suppliers discussing lead free PCB considerations. Within the document, it mentions black pad being associated with tented vias. Thanks John S.
Electronics Forum | Tue Jan 31 15:44:08 EST 2006 | John S.
We're looking at lead free surface finishes for some of our products. On one supplier's site, I found a note that tenting vias on ENIG boards can lead to the black pad phenomenon. How does this compare to your design guidelines and experience? Than
Used SMT Equipment | In-Circuit Testers
JDSU FST-2802-V6 Acterna Ethernet and Fibre Channel services module with FST2000 TestPad The FST2802 is a handheld Ethernet, Fibre Channel, and IP services test instrument designed to meet the needs of service providers for turning up and troub
Used SMT Equipment | In-Circuit Testers
JDSU FST-2802 Acterna Ethernet and Fibre Channel Services Module The FST-2802 is a handheld Ethernet, Fibre Channel, and IP services test instrument designed to meet the needs of service providers for turning up and troubleshooting these variou
Industry News | 2011-01-12 17:48:44.0
GPD Global will highlight its Positive Cavity Displacement (PCD) Dispensing in Booth #6111 at the upcoming Automation and Technology West Expo (ATX), scheduled to take place February 8-10, 2011 at the Anaheim Convention Center in Anaheim, CA.
Industry News | 2011-11-20 13:36:13.0
GPD Global has been awarded two Global Technology Awards in the categories of Adhesives/Coatings/Encapsulants and Dispensing Equipment for its PCD Dispensing on the MAX Series Platform
Parts & Supplies | Circuit Board Assembly Products
1). 80 *190mm/2up, FR-4 2). 6 layers at 1.4mm thick 3). 35 μm copper weight 4). Green solder mask LPI/White legend 5). ENIG surface finish 6). Blind via from Layer 1 to layer 2 7). Via in pad plugged conductive resin
Parts & Supplies | Circuit Board Assembly Products
1). 100mm x 98mm/1up, FR-4, 2). 1mm +/-0.1mm,6 Layers 3). 1oz copper finished 3). Green solder mask/white legend 4). Min. hole 0.15mm, 4/4 mil track/gap 5). Blind via layer 1-2, via-in-pad. 6). Immersion gold surface finish
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
To see more visit Pillarhouse here: https://www.pillarhouse.co.uk/products/selective-soldering-handload/pilot-handload Economical, compact, single point selective soldering system The all-new ultra-low-cost Pilot machine has been designed as an ent
The PCB Footprint Expert is a powerful CAD library development tool powered by our own proprietary CAD LEAP Technology (Libraries Enhanced with Automated Preferences). It is packed with very powerful advanced library management features that cuts foo
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Thu Oct 03 00:00:00 EDT 2019 - Thu Oct 03 00:00:00 EDT 2019 | ,
IPC Tech Ed Webinar Series: Ball Grid Array (BGA) and Bottom Termination Component (BTC) Design and Assembly Challenges: Reflow Profiling to Achieve Low Defect Rates and Successful Assembly! – Part 2
Career Center | , | Engineering,Sales/Marketing,Technical Support
Applications Engineer with over 20 years of combined Manufacturing/Field Service/Applications Engineering experience in the SMT industry.
SMTnet Express, July 16, 2020, Subscribers: 28,512, Companies: 11,045, Users: 25,964 Via In Pad - Conductive Fill or Non-Conductive Fill? Credits: Advanced Circuits In the early 2000s the first fine-pitch ball grid array devices became popular
| https://pcbasupplies.com/ezload-replacment-pads/
ezLOAD Replacment Pads Login Create Account Contact View My Cart Menu × Categories Hand Soldering & Rework Automation Tooling PCB Support Systems Soldering Robots Material Handling Dry Storage Cabinets Component Handling Selective Solder Nozzles Pick
Heller Industries Inc. | https://hellerindustries.com/intermetallics-growth/
Intermetallic Growth on PCB - Heller Home » Intermetallic Growth on PCB Re-printed in partnership with ITM Intermetallic Growth on PCB Where the tin-lead solder adheres to the copper of the lead (from plating) and to the pad
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411