Baker offers a complete line of standard and custom wet process equipment/tools to the global PCB and PV industries.
New Equipment | Assembly Services
G9 + automatic vision printing machine is a new product for SMT high-end application field, which can perfectly meet the process requirements of 03015, 0.25pich and other fine spacing, high precision and high speed. Introduction to standard function
The DV-7000 Heli-Flow® pump is a third-generation encoded auger pump. The pump has a floating head for use with footed needles to make fast, repeatable dots of solder paste and silver epoxy. The dispense gap is mechanically controlled by the needle,
Electronics Forum | Tue Jul 31 18:46:40 EDT 2007 | rpadilla
Well, everyone has provided good advice, but if you are looking for a wave flux that can provide much better dwell times and consistent wetting throughout the hole fill, without making adjustments to your production process, I suggest going with Senj
Electronics Forum | Thu Oct 12 22:36:40 EDT 2017 | stefan110882
Please ost some pictures so we can see what > you're talking about. OK here an example. I'm sorry for the bad quality - The picture is cropped and only one of two pictures that I had on the phone that I could use. According to my supervisor, th
Used SMT Equipment | Screen Printers
DEK Horizon 03iX Fully Automatic Screen Solder Paste Printer Model Horizon 03iX Operating System Win XP+09sp13 or up PCB support Tooling&n
Used SMT Equipment | Screen Printers
DEK Horizon 03iX SMT Printer Model Horizon 03iX Operating System Win XP+09sp13 or up PCB support Tooling Magnetic tooling pins Camera type Hawkeye 750 or Hawkeye 1700 (optional) 198040 198043 hawkeye Board foil clamp siz
Industry News | 2016-08-25 17:56:34.0
GPD Global's advanced Precision Auger Pump retrofits into your dispensing system to provide excellent dispense control and repeatability. Precision Auger Pump Integration provides your process development with a broad range of functionality.
Industry News | 2018-10-08 20:18:03.0
GPD Global will exhibit at the upcoming SMTA International 2018. At booth# 517, see our automated Conformal Coating Machine with excellent repeatability for under $40,000.
_1.jpg)
Parts & Supplies | Pick and Place/Feeders
JUKI FEEDER part E513070600B E9630729000 T AC SERVO MOTOR(TS4632N2020E600) E9630755000 RERAY UNIT E96307800A0 HEAD SENSOR ASM E963171500A DUCT (KD-76-03-C) E963171500B DUCT (KD-76-045-C) E963171500C DUCT (KD-76-085-C) E9631721000 LAHD SENSOR
_1.jpg)
Parts & Supplies | Pick and Place/Feeders
JUKI FF 44MM feeder tape guide E72037060AC E9630729000 T AC SERVO MOTOR(TS4632N2020E600) E9630755000 RERAY UNIT E96307800A0 HEAD SENSOR ASM E963171500A DUCT (KD-76-03-C) E963171500B DUCT (KD-76-045-C) E963171500C DUCT (KD-76-085-C) E96317210
Technical Library | 2017-10-19 01:17:56.0
Wetting balance testing has been an industry standard for evaluating the solderability of surface finishes on printed circuit boards (PCB) for many years. A Wetting Balance Curve showing Force as a function of Time, along with the individual data outputs "Time to Zero" T(0), "Time to Two-Thirds Maximum Force" T(2/3), and "Maximum Force" F(max) are usually used to evaluate the solderability performance of various surface finishes. While a visual interpretation of the full curve is a quick way to compare various test results, this method is subjective and does not lend itself readily to a rigorous statistical evaluation. Therefore, very often, when a statistical evaluation is desired for comparing the solderability between different surface finishes or different test conditions, one of the individual parameters is chosen for convenience. However, focusing on a single output usually doesn't provide a complete picture of the solderability of the surface finish being evaluated.In this paper, various models here-in labeled as "point" and "area" models are generated using the three most commonly evaluated individual outputs T(0), T(2/3), and F(max). These models have been studied to quantify how well each describes the full wetting balance curve. The solderability score (S-Score) with ranking from 0 to 10 were given to quantify the wetting balance curve as the result of the model study, which corresponds well with experimental results.
Technical Library | 2013-10-13 10:54:13.0
The measurement of the conformal coating thickness on a printed circuit board (PCB) to ensure internal and international standards are met is now a critical factor in conformal coating process control. There are several methods for measurement of conformal coating thickness and they fall into two categories. These categories are wet film measurements applied during coating application and dry film measurements made after the coating is dried enough not to damage the coating.
Momentum was designed and built to be a no-nonsense production machine. Cost-efficient and featuring a modest footprint, it grows with the user; innovative patented features can be added on or retrofitted as needed as the user’s throughput dema
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Career Center | Oldsmar, Florida USA | Engineering,Maintenance,Production
Job Title: Assembler 2 – IPC 610 – 1st Shift Address: 3655 Tampa Rd, Oldsmar FL 34677 Duration: 1 year Pay Rate: $15-$18 Hours: 9/80 schedule Monday – Thursday 6:00AM – 3:30PM, Friday 6:00AM to 2:30PM Job Description: Use microscope to verify
Career Center | Oldsmar, Florida USA | Maintenance,Production
Job Description: • Uses microscope to verify correct part placement and orientation, manually align parts before soldering and perform post re-flow inspection and touch-up. • Able to identify and touch up poor wetted solder joints, solder voids / i
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
SMTnet Express, November 19, 2017, Subscribers: 30,938, Companies: 10,768, Users: 23,942 To Quantify a Wetting Balance Curve Frank Xu Ph.D., Robert Farrell, Rita Mohanty Ph.D.; Enthone Wetting balance testing has been an industry standard
| http://etasmt.com/cc?ID=te_news_industry,24564&url=_print
. According to the IPC standard, non-wetting is defined as the inability of molten solder to form a metallic bond with the base metal. This results in the PCB pads or the
Precision PCB Services, Inc | https://precision-pcb-services-inc.com/products/amtech-nws-4400-ha-tf-water-washable-lead-free-tacky-solder-flux-rem1
. – REM1 flux classification – Optimized for lead-free and standard alloy systems – Wide process window – Excellent wetting compatibility on most board finishes
