Electronics Forum | Thu Jan 22 11:15:08 EST 2009 | slthomas
I got mine from my used equipment broker, and it was version 1.5. I would try wherever you get your spares from. My recollection is that the "free" versions (1.5 and older) are not available through Assembleon anymore and that the current version
Electronics Forum | Mon Aug 25 02:57:43 EDT 2014 | arjunkolavara
We are in the process of qualifying our SMT lines for the High Melting Point Solder with alloy composition of 93.5 Pb 5 Sn 1.5 Ag.If any one has already an experience with this alloy,kindly do give ur inputs on the process of profiling . The reflow d
Electronics Forum | Mon Aug 14 00:19:29 EDT 2017 | pandamw
Model : PDDC400-292_A 50 Ohm 2-way 2.92mm-Female Resistive Power Divider From DC to 40GHz Rated at 1Watts; 40GHz, 2.92mm-Female Resistive Power Divider; Insertion Loss 1.5dB; Isolation 10dB; Operating Temperature -40 to +70℃. Frequency Range | GHz
Electronics Forum | Mon Oct 26 13:38:35 EDT 2009 | davef
Type K thermocouples are the most commonly used in the electronics industry. There are various types of thermocouple types that can be used. Examples include [Ray Prasad]: • Type K ¾ nickel-chromium vs. nickel-aluminum (most commonly used); tempera
Electronics Forum | Mon Aug 21 10:47:48 EDT 2006 | FredC
Hello Mika, I just checked a windmill and a test nozzle we have on the bench. The useful travel of the nozzle before the risk of the crosspin getting stuck in the loading gate is 1.5mm, if it gets stuck it is the nozzle is 1.7 up. If the cross pin is
Electronics Forum | Sat Nov 04 22:26:33 EST 2000 | Aoki Laboratories Ltd.
Greg, The operating parameters for Wave Soldering are: 1. Preheat Temp. (80-110 c, board surface); 2. 1.5-3 secs dwell time in solder. This, 1.5 second, is the time required for both the lead and solder to gain sufficient heat and as a result "tinn
Electronics Forum | Tue Jun 17 08:52:39 EDT 2003 | russ
Aspect ratio = width of aperture divided by height. E.G. 6 mil stencil at 9 mil wide = aspect ratio of 1.5. Value should be 1.5 min. Area ratio - use when length and width of pad are roughly same dimension like for BGAs and 0805 and smaller R-nets
Electronics Forum | Tue Jun 15 16:16:29 EDT 2004 | Igor
Our research group is looking for a more efficient method of coating a small piece of sheet metal. We have a 1.5cm x 1.5cm very thin sheet of metal that we are coating with liquid epoxy, using a brush that was provided. This method has become unacc
Electronics Forum | Fri Jul 15 10:56:19 EDT 2005 | pr
As Russ said, you do a DOE beforehand. BUT Maybe we are missing something, we do SPC after the wave (1/5) to catch defect trends and fix them with a minimum of inspection. If you are running a 2,000 piece pull, are you that confident that your origin
Electronics Forum | Mon Nov 20 19:49:03 EST 2006 | davef
Sorry for stating this incorrectly. It should been: Bow & twist for bare boards and panels: IPC-A-610 Acceptability of Electronic Assemblies, 10.6: 1.5% for PTH only and 0.75% for SMT, acording to test method TM-650, method 2.4.22 IPC-6012, par. 3.
