Technical Library | 2017-05-04 17:35:01.0
Most of today's printed circuit board base materials are anisotropic and it is not possible to use a simple method to measure thermal conductivity along the different axis, especially when a good accuracy is expected. Few base material suppliers' datasheet show X, Y and Z thermal conductivities. In most cases, a single value is given, moreover determined with a generic methodology, and not necessarily adapted to the reality of glass-reinforced composites with a strong anisotropy.After reminding of the fundamentals in thermal science, this paper gives an overview of the state-of the art in terms of thermal conductivity measurement on PCB base materials, and some typical values. It finally proposes an innovative method called transient fin method, and associated test sample, to perform reliable and consistent in plane thermal conductivity measurement on anisotropic PCB base materials.
Technical Library | 2020-09-16 21:24:56.0
Additive manufacturing processes typically used for mechanical parts can be combined with enhanced technologies for electronics production to enable a highly flexible manufacturing of personalized 3D electronic devices. To illustrate different approaches for implementing electrical and electronic functionality, conductive paths and electronic components were embedded in a powder bed printed substrate using an enhanced 3D printer. In addition, a modified Aerosol Jet printing process and assembly technologies adapted from the technology of Molded Interconnect Devices were applied to print circuit patterns and to electrically interconnect components on the surface of the 3D substrates.
Institute for Factory Automation and Production Systems (FAPS)
Technical Library | 2020-11-29 22:02:49.0
It has been over 25 years since the earliest edition of "Everything You Ever Wanted to Know About Laminates...but Were Afraid to Ask" was pounded out on an old TRaSh-80 Computer. It has undergone periodic review and editing, including adaption for use on our website. (When I entered the industry Al Gore had not yet invented the internet.) Before I "retired" in 2004, we did another minor revision, but it was largely cosmetic, removing most references to the old military specification and introducing IPC-4101, the "new" specification for laminate and prepreg materials.
Technical Library | 2021-11-22 20:32:10.0
The aim of this work is to define a procedure to develop diagnostic systems for Printed Circuit Boards, based on Automated Optical Inspection with low cost and easy adaptability to different features. A complete system to detect mounting defects in the circuits is presented in this paper. A low cost image acquisition system with high accuracy has been designed to fit this application. Afterward, the resulting images are processed using the Wavelet Transform and Neural Networks, for low computational cost and acceptable precision. The wavelet space represents a compact support for efficient feature extraction with the localization property. The proposed solution is demonstrated on several defects in different kind of circuits.
Technical Library | 2015-02-12 13:32:52.0
Market forces, particularly legislation against the use of lead in electronics, have driven electronics manufacturers towards lead-free solders for PCB assembly and rework. This approach creates challenges because of the relatively high temperatures needed for lead-free soldering. Additionally, lead-free solder alloys typically do not wet or wick as easily as Sn63Pb37 leaded types. As PCBs often include both BGAs and simpler discrete devices, a lead-free rework capability should include a suitable soldering station and a BGA rework station. This article shows how such equipment can be adapted to overcome the lead-free issues and provide a successful reworking facility.
Technical Library | 2015-07-14 21:32:04.0
The PCB industry is ever changing and adapting to new technologies. OEM specifications and requirements have also advanced due to these technologies. In some cases the OEMs are asking for a low resistance test to be performed on some or all electrical test nets of the PCB or on the holes of the PCB. This requirement is typically not well defined on the fabrication drawing and that leads to misleading conclusions by the fabrication house (...) This paper will use the data gathered by the company’s operations to outline what a 4-wire Kelvin test is and how it can be used. Several examples will be illustrated of what the 4 wire Kelvin test can and cannot do. A clear definition of what limitations are present during the testing operation will be defined. The paper will assist designers in understanding how the low resistance test can assist them and also identify causes that can identify unwanted concerns/issues.
Technical Library | 2017-04-20 19:16:17.0
IST AG thin film mass flow sensors offer solutions for a wide variety of flow applications. The thin film and membrane technologies incorporate highly accurate temperature sensors and heaters as core elements of the sensors. IST AGs flow sensors are applicable in gas (liquids upon request), have an operating temperature range of -30 °C to +450 °C, and can measure low rate and direction from 0.0001 m/s (microflowSens) to 100 m/s (respectively from 1 mL/min to 10 L/min). In addition to measuring flow rates, our sensors can detect the presence of a liquid, biofilm or bubbles as well as indicate liquid level. Development channels guarantee the best possible adaptation of our sensors, whether in terms of dynamic range, response time, directional detection or ambient conditions.
Technical Library | 2016-06-16 15:29:31.0
Embedding components within the PC board structure is not a new concept. Until recently, however, most embedded component PC board applications adapted only passive elements. The early component forming processes relied on resistive inks and films to enable embedding of resistor and capacitors elements. Although these forming methods remain viable, many companies are choosing to place very thin discrete passive components and semiconductor die elements within the PC board layering structure. In addition to improving the products performance, companies have found that by reducing the component population on the PC board's surface, board level assembly is less complex and the PC board can be made smaller, The smaller substrate, even when more complex, often results in lower cost. Although size and cost reductions are significant attributes, the closer coupling of key elements can also contribute to improving functional performance.This paper focuses on six basic embedded component structure designs described in IPC-7092.
Technical Library | 2014-10-30 01:48:43.0
The ultimate life of a microelectronics component is often limited by failure of a solder joint due to crack growth through the laminate under a contact pad (cratering), through the intermetallic bond to the pad, or through the solder itself. Whatever the failure mode proper assessments or even relative comparisons of life in service are not possible based on accelerated testing with fixed amplitudes, or random vibration testing, alone. Effects of thermal cycling enhanced precipitate coarsening on the deformation properties can be accounted for by microstructurally adaptive constitutive relations, but separate effects on the rate of recrystallization lead to a break-down in common damage accumulation laws such as Miner's rule. Isothermal cycling of individual solder joints revealed additional effects of amplitude variations on the deformation properties that cannot currently be accounted for directly. We propose a practical modification to Miner's rule for solder failure to circumvent this problem. Testing of individual solder pads, eliminating effects of the solder properties, still showed variations in cycling amplitude to systematically reduce subsequent acceleration factors for solder pad cratering. General trends, anticipated consequences and remaining research needs are discussed
Technical Library | 2015-05-28 17:34:48.0
The printed circuit board assembly industry has long embraced the "Smaller, Lighter, Faster" mantra for electronic devices, especially in our ubiquitous mobile devices. As manufacturers increase smart phone functionality and capability, designers must adopt smaller components to facilitate high-density packaging. Measuring over 40% smaller than today's 0402M (0.4mmx0.2mm) microchip, the new 03015M (0.3mm×0.15mm) microchip epitomizes the bleeding-edge of surface mount component miniaturization. This presentation will explore board and component trends, and then delve into three critical areas for successful 03015M adoption: placement equipment, assembly materials, and process controls. Beyond machine requirements, the importance of taping specifications, component shape, solder fillet, spacing gap, and stencil design are explored. We will also examine how Adaptive Process Control can increase production yields and reduce defects by placing components to solder position rather than pad. Understanding the process considerations for 03015M component mounting today will help designers and manufacturers transition to successful placement tomorrow.
.gif)
