Used SMT Equipment | Soldering - Wave
BASE-EC Electra Base Machine 1 CE-WS CE Compliance 1 RGDI-EC Rigid Intermix Fingers 1 FMSK-EC Finger Mask 2 FANS-WS Cooling Fans Option 1 VEC-EC Vecta Heater 2 IR-EC Infrared Heater 1 TOPIR-EC Top Infrared Heater 1 O2-WS OptiFlux II 1 O2SLCT
Used SMT Equipment | Soldering - Wave
Speedline/Electrovert Electra Wave Solder System, Model 500F, 480V, CE, (2) Upper Convection Pre Heaters, (1) Bottom IR Pre Heater, (2) Bottom Vecta Heaters, External Monitor, Lambda Wave, Rotary Chip Wave, Air Knife, No Fluxer Auction Item: www.x
Used SMT Equipment | Soldering - Wave
Model Specifications: Date 12/98 440 Volts Three Phase 46 KVA 60 Hz 20" L/R N2 Rotary Chip Contour Bar Feeder Exit Photo Eye Light Tower 3 Bottom Vectra Heat VVL Intermix 3.0- 1/16" fingers Ceramic Aerators 12" Load Guides Finger Cleaner
Used SMT Equipment | Soldering - Wave
BASE-EC Electra Base Machine 1 CE-WS CE Compliance 1 RGDI-EC Rigid Intermix Fingers 1 FMSK-EC Finger Mask 2 FANS-WS Cooling Fans Option 1 VEC-EC Vecta Heater 2 IR-EC Infrared Heater 1 TOPIR-EC Top Infrared Heater 1 O2-WS OptiFlux II 1 O2SLCT
Used SMT Equipment | Pick and Place/Feeders
The Auction : UNIVERSAL GSM 3 Feet Conveyor Universal GSM2 Placement Machine Universal GSM Placement Machine Universal GSM PTF ELECTROVERT ELECTRA 500/F Wave Soldering Machine Lot Informations: Year:2000 Manufacturer:ELECTROVE
Industry News | 2009-04-08 16:37:18.0
MADISON, AL � April 2009 � STI Electronics Inc., a full service organization providing training, electronic and industrial sales and distribution, consulting, laboratory analysis, prototyping, and small- to medium-volume PCB assembly, announces that Jim Raby, its founder and technical director, will give a Keynote Presentation titled, �Past, Present and Future of Electronic Assemblies� at SMTA Huntsville, scheduled to take place on Tuesday, April 14 from 8:30-9 a.m.
Electronics Forum | Wed Jul 19 16:28:31 EDT 2000 | Boca
Kinda along the lines 'if it comes we will build it'. Perhaps you can assemble it, I've not done it, but a question to ask a bit earlier is - should we. Check the specifications for the component, published by component vendor. Most of them really
Electronics Forum | Tue Aug 13 15:55:10 EDT 2002 | jseagle
I am looking for advice on purchasing a used '98-'00 Electrovert Electra wave soldering machine. Are there any specific parts of the machine I should closely inspect? Any specific options I should make sure it has? I will need it to have a spray f
Electronics Forum | Wed Nov 10 11:31:06 EST 1999 | John Thorup
Hello Horace You're lucky in that you have two of the same machine. You should be able to arrive at the root of the problem by comparison. The problem is likely to occur in one or more of these areas: MACHINE: As said , pump speed and air contact ar
Electronics Forum | Tue Aug 17 09:59:50 EDT 1999 | Earl Moon
I'm trying a second time to post this very important message, to me, concerning Air-Vac's following creation. Does any own and use this stuff successfully to remove solder from 20 layer and up MLB's with .020" diameter holes? Also, is any of the adve