Technical Library: flexible board (Page 2 of 23)

Fiducial Marks

Technical Library | 2019-06-17 15:09:43.0

Very often pick and place machines are programmed using CAD data. This data increases the accuracy, precision, and repeatability of its component placement objectives. CAD data makes fine pitch and small component assemblies repeatable, but cannot adjust to a particular board unless it is exactly the same size and shape of the original board used for programming. The process by which printed circuit boards (PCBs) are made only allows some minor changes inboard size and shape, but these small differences are enough for parts to be misplaced. For this reason we use fiducial marks to increase the chances of precise component alignment.

ACI Technologies, Inc.

Investigation of PCB Failure after SMT Manufacturing Process

Technical Library | 2019-10-21 09:58:50.0

An ACI Technologies customer inquired regarding printed circuit board(PCB) failures that were becoming increasingly prevalent after the SMT (surface mount technology) manufacturing process. The failures were detected by electrical testing, but were undetermined as to the location and specific devices causing the failures. The failures were suspected to be caused predominately in the BGA (ball grid array) devices located on specific sites on this 16 layer construction. Information that was provided on the nature of the failures (i.e., opens or shorts) included high resistance shorts that were occurring in those specified areas. The surface finish was a eutectic HASL (hot air solder leveling) and the solder paste used was a water soluble Sn/Pb(tin/lead).

ACI Technologies, Inc.

BGA Placement on Rework Station

Technical Library | 2019-06-12 10:33:58.0

The success of ball grid array (BGA) placement on electronic assemblies is as much a matter of proper preparation and planning, as it is technique. In some designs, it is more appropriate to apply BGAs using a rework station that isolates the placement of the device, without subjecting the entire assembly to thermal reflow. This is especially beneficial in board constructions where the number of BGAs is limited, and the application of the solder paste is difficult, due to small pitch features that stretch the limitation of the stencil construction. Another application for rework stations, involves very large and thermally conductive BGAs, which will not uniformly reflow with other components on the assembly, and may require special process parameters for their proper placement. The most common use of BGA rework stations are for assemblies requiring BGA removal and replacements due to failures in the initial assembly stage.

ACI Technologies, Inc.

Conformal Coating Inspection

Technical Library | 2019-05-21 17:31:39.0

In the field of electronics manufacturing, the end use of the product will always dictate the processes, procedures, and methods, not only for building the product, but also for testing, cleaning, and protecting the assembly in order to assure the level of quality required for proper operation. The need to protect an electronic assembly from its end use environment may stem from anyone of a number of hazardous (or potentially hazardous) conditions. Choosing the type of protective material is dependent upon matching that material’s characteristics with the conditions to be overcome. Naturally, the use of a protective (conformal) coating will require some method of verification to ensure the desired level and type of protection is achieved.

ACI Technologies, Inc.

Use of Pelseal® 2078 Viton® Caulk in Decapsulation of Electronics Components

Technical Library | 2019-06-18 10:18:00.0

ACI Technologies is tasked with decapsulation of electronics components for testing and investigative purposes. In the normal method of decapsulation, an analyst will drill a small indentation, with a rotary tool, in the hermetic sealant material and then apply Nitric acid to eat through the polymeric encapsulant.

ACI Technologies, Inc.

Advanced Packaging of SMT Assemblies for Greater Cost Reduction

Technical Library | 2019-06-06 13:40:47.0

Legacy electronics assemblies, such as through-hole (Figure 1) and connectorized component packages, are robust and prevalent throughout industry. However, each of these assembly methods have reached their limits in terms of weight, volume, reliability, and most importantly cost. With cost reduction of assemblies now the primary focus area throughout the electronics industry, there is more of a need than ever to implement the latest advancements in surface mount technology (SMT) into electronics assembly designs. Although SMT has been utilized in the electronics industry for many years, implementation of the technology is still in the ever-evolving process of reducing component footprint size, component spacing, and component I/O pitch. Implementation of the most up-to-date SMT processes provides optimal weight, volume, and cost savings, for any type of assembly.

ACI Technologies, Inc.

Virtual Manufacturing

Technical Library | 2019-09-16 09:41:02.0

“What is Virtual Manufacturing?” The simplest answer is a manufacturing simulation using a computer. The more complete answer is that virtual manufacturing is the process of designing a model of a real system and conducting experiments with this model for the purpose of understanding the behavior of the system. In today’s complex manufacturing environment, processes must be completely understood before implementation in order to “get it right the first time.” To achieve this goal, the use of a virtual environment is essential for simulating individual manufacturing processes and the total manufacturing system. By driving compatibility between the product design and the assembly plant process, these virtual tools enable the early optimization of cost, quality, and time to help achieve integrated products, process and resource design, and affordability.

ACI Technologies, Inc.

Flip Chip Attach Techniques

Technical Library | 2019-05-21 17:38:55.0

Last month we presented Flip Chip Rework.As promised, this month we follow up with attachment techniques. Flip chip assembly is a key technology for advanced packaging of microelectronic circuits. It allows attachment of a bare chip to a packaging substrate in a face-down configuration, with electrical connections between the chip and substrate via conducting “bumps.” Flip chip technology was first invented by IBM for mainframe computer application in the early 1960s. Semiconductor devices are mounted face down and electrically and mechanically connected to a substrate (Figure 1). IBM called this manufacturing process a C4 process (controlled collapse chip connection).

ACI Technologies, Inc.

PCB Laser Depanelizing Using a UV Laser

Technical Library | 2016-10-06 15:13:02.0

One of the methods gaining in popularity for singulating rigid/flex, rigid and flex circuit boards post assembly is through the use of laser routing. This method has the advantage of speed, positional accuracy, no tooling wear and lastly no induced mechanical stresses on components during the singulating process.

BEST Inc.


flexible board searches for Companies, Equipment, Machines, Suppliers & Information

Flux-Free Reflow Soldering

Real Time Process Control BREAKTHROUGH for Dispensing Industry.
Used SMT Equipment Auction Spartronics

World's Best Reflow Oven Customizable for Unique Applications
PCB Handling Machine with CE

MSD Dry Cabinets
smt assembly equipment manufacturer

MSD storage in desiccant dry canbinets