Electronics Forum | Fri Oct 31 06:55:35 EDT 2008 | andrzej
Answer on point 2 - I understand you send him gerbers of single PCB (?). In most cases you have panelized PCBs so to avoid problems with stencil first you should order PCBs and ASK your PCB supplier to send you back his gerbers of panel. There are so
Electronics Forum | Fri Sep 01 05:29:01 EDT 2017 | mona0312
Hi, Recently, i found a company called "jlcpcb". It’s very cheap 10pcs boards. 1.2mm thick, 1-OZ copper, 6/6-mil outer (0.1525mm) just cost $2 Cheap price and lots of options regarding board thickness, colour, etc. None of my boards have ever had a
Electronics Forum | Wed Jan 13 04:27:00 EST 2016 | crystalpcb
Hi Here is our factory production capability: Shenze Electronic PCB Specification Layer Count 1 to 35 Layers Material Brand Shengyi,KB,GRACE,ISOLA,Rogers,Taconic,ARLLON,Bergquist Base Material FR-4（TG135,TG150,TG170,TG180），Halogen Free FR-4，Ceramic
Electronics Forum | Wed Jul 16 19:38:28 EDT 2014 | garym4569
What is the base cost of an inline pcb etcher? Specs: fiducial alignment, smema interface, 400mm x 400mm marking area. Will be used to mark panel 2d codes, pcb array 2d codes, and human readable. Thanks Gm
Electronics Forum | Thu Aug 12 14:17:19 EDT 2010 | mikesewell
You might reduce your panel size, cut it in half and rotate to better utilize your edge clamping/board supports. Tape off your current stencil and see if it improves the print. A new stencil and a little extra handling may be cheaper than tooling.
Electronics Forum | Wed Aug 11 18:35:17 EDT 2010 | julie1
Anyone work with or have knowledge about metal core/clad boards? The board I'm working with is approximately 2" X 3/4" aluminum core pcb, in a 56 up array. There are 3 LED placements per board. I'm having trouble getting a consistent screen print.
Electronics Forum | Mon Oct 24 06:31:31 EDT 2022 | richardcargill
We have a similar board and came up with a quick and dirty solution. The board locates via pins onto a manual desk press with strategically placed feet to break the mouse bite. Not really much quicker than doing it all by hand, but after a thousand p
Electronics Forum | Sun Nov 01 23:51:44 EST 2009 | boardhouse
Hi Julie, My opinion is that the top board would not pass IPC, solder mask encroachment on pads. Second board is what we call Orange peel,this can be caused two way's. 1) the solder mask was not tack dried enough prior to imaging which caused artwo
Electronics Forum | Thu Sep 13 02:52:44 EDT 2018 | directx995
Machines don't have any kinda of local correction on specific offset on PCB, you can only edit main board and it will reflect on all other offsets in panel. For some high running projects we merged 2 pick and places into one (for example 0 degree rot
Electronics Forum | Thu Aug 22 07:48:30 EDT 2002 | Dave Milk
While separating individual pcbs from a panel, operators have caused delamination of the edge of the board, at the tabs that were cut. How can these boards be repaired? The delamination causes them to fail J-STD-001C 9.2.1.1.d. Also, what would yo
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
