Electronics Forum: 2015 (Page 148 of 162)

Mydata Hydra tool reference marks error

Electronics Forum | Mon Jun 15 17:54:38 EDT 2015 | catsem23

Hi I have been having a problem with my Hydra tool reference plate. Machine keeps stopping and comes up with error message - failed to locate hydra tool reference marks & Error mounting component .... from feeder ..... with nozzle .... I have check

SMT control management software

Electronics Forum | Tue Jul 14 02:45:40 EDT 2015 | alexeis

Hi, I agree that the existing systems sometimes difficult to implement. Also, as a large system so its maneuverability is low in spite of all the beautiful tools. Usually if you need something you do not find anything there. We, as a software compan

Which AOI would you recommend?

Electronics Forum | Wed Jun 24 08:40:00 EDT 2015 | bdamico

Hello Shim, You may want to consider reading this thread on the forum. http://www.smtnet.com/Forums/index.cfm?fuseaction=view_thread&CFApp=1&Thread_ID=17947&#Message73545 I am a bit biased as I own MIRTEC here in the US, but we would be more tha

Which AOI would you recommend?

Electronics Forum | Wed Jul 29 01:58:08 EDT 2015 | buckcho

Hello, there are several great machines you can choose from. I would recommend making a benchmark, if you can. You chose 4 machines that meet you requirements (mostly prize range) and make them program and debug one of your products. After that insp

pad cratering

Electronics Forum | Wed Jul 01 13:17:39 EDT 2015 | davef

Cheryl Tulkoff and Randy Schueller do a good job summarizing the thinks on pad cratering here: http://www.smta.org/chapters/files/uppermidwest_padcratering.pdf Potential Mitigations to Pad Cratering * Board Redesign * Solder mask defined vs. non-s

Conceptronic HVA102 request for help

Electronics Forum | Fri Jul 10 15:28:47 EDT 2015 | sumote

I could really use some help, My oven is continually blowing one of the SFC fuses (the one on the left as it sets in the machine) when the conveyor tries to run. It appears that the traces on the circuit card were having too much current pulled th

Help with resources for SMT assembly

Electronics Forum | Sat Jul 25 18:35:33 EDT 2015 | orbitcoms

I am looking for information regarding setting up an SMT assembly line. I have recently purchased a stencil paste printer, pick and place, and reflow oven. The main information I need is the paste selection and best finish material on the PCBs. I wil

Help with resources for SMT assembly

Electronics Forum | Sun Jul 26 07:09:25 EDT 2015 | orbitcoms

Thank you for your prompt response. The boards we have made for us current are Immersed Gold treated because we have been hand soldering and needed flat finish that would solder ok without tarnishing too quickly. I will take a look at the link you pr

Can we check polarity and upside downs on My100?

Electronics Forum | Thu Jul 30 17:31:41 EDT 2015 | dyoungquist

We are running a Mydata (Micronic) MY15E. The MY100 is the next generation after the MYxxE series. As far as I know, there is no way for the machine itself to check the polarity of ICs to see if 1 or more are in the tube or reel different from all

Can Atmega328P-PU be used to replace the burnt atmega328 on Arduino UNO?

Electronics Forum | Sun Aug 02 23:12:25 EDT 2015 | galler

For anyone having problems in burning boot loader in an Atmega328, the burnt atmega328 should be the most common tricky problem. some makers users are looking for an alternative to replace it. Now some say that Atmega328P-PU could be a great alternat


2015 searches for Companies, Equipment, Machines, Suppliers & Information