Electronics Forum | Wed Oct 06 00:26:04 EDT 1999 | Karlin
| Hi, | | Help! Could anyone help to enlighten me on this? | | Question: | | If I have a CSP/BGA package of size X by Y and the standoff gap between the component and PCB is Z, What is the maximum allowable Y/Z or X/Z that using a normal water cl
Electronics Forum | Wed Oct 06 08:41:42 EDT 1999 | Dave F
| | Hi, | | | | Help! Could anyone help to enlighten me on this? | | | | Question: | | | | If I have a CSP/BGA package of size X by Y and the standoff gap between the component and PCB is Z, What is the maximum allowable Y/Z or X/Z that using a n
Electronics Forum | Wed Oct 06 12:03:12 EDT 1999 | Graham Naisbitt
| | Hi, | | | | Help! Could anyone help to enlighten me on this? | | | | Question: | | | | If I have a CSP/BGA package of size X by Y and the standoff gap between the component and PCB is Z, What is the maximum allowable Y/Z or X/Z that using a n
Electronics Forum | Fri Oct 08 02:31:07 EDT 1999 | Brian
| | | | Hi, | | | | | | | | Help! Could anyone help to enlighten me on this? | | | | | | | | Question: | | | | | | | | If I have a CSP/BGA package of size X by Y and the standoff gap between the component and PCB is Z, What is the maximum allowab
Electronics Forum | Thu Dec 01 13:24:45 EST 2011 | kmakiya
Sounds like you have a bad heater. Check current on each leg of the heater circuit, CON6 for the wash and CON7 for the rinse. The current should be the same on each leg. Trek is now part of Stoelting, tech support is 920-894-2293. Hope this helps if
Electronics Forum | Wed Oct 06 23:36:28 EDT 1999 | karlin
| | | Hi, | | | | | | Help! Could anyone help to enlighten me on this? | | | | | | Question: | | | | | | If I have a CSP/BGA package of size X by Y and the standoff gap between the component and PCB is Z, What is the maximum allowable Y/Z or X/Z
Electronics Forum | Thu Aug 13 16:46:13 EDT 2009 | snsmt
Hello Everyone, I have noticed that everytime that we have ran a PCB with fine pitch components (or even 0603s), there are little white strands on the leads or on top of the components. It occurs on both lead and lead free solder. We usually soak
Electronics Forum | Thu Nov 02 13:17:06 EDT 2017 | jardcrocker
Hi...i have a question. After you solder a circuit board, what do you wash the flux residue off with? I am hesitant to use water for fear of subsequent corrosion, and have no clue as to what kind of flux is in my solder wire. automated pcb assembly
Electronics Forum | Wed Oct 06 11:40:41 EDT 1999 | Debbie Alavezos
| | Hi, | | | | Help! Could anyone help to enlighten me on this? | | | | Question: | | | | If I have a CSP/BGA package of size X by Y and the standoff gap between the component and PCB is Z, What is the maximum allowable Y/Z or X/Z that using a n
Electronics Forum | Wed Oct 06 03:58:25 EDT 1999 | Brian
| | Hi, | | | | Help! Could anyone help to enlighten me on this? | | | | Question: | | | | If I have a CSP/BGA package of size X by Y and the standoff gap between the component and PCB is Z, What is the maximum allowable Y/Z or X/Z that using a n
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830