Electronics Forum | Mon Mar 16 04:46:25 EST 1998 | Grant Petty
We have just go another batch of PCB's from our loaders, and some of the boards are severely warped. The boards are PCI cards and one of the boards is 9mm out at one end. The PCB is 210mm long and 4 layers. I am wondering if anyone knows what could
Electronics Forum | Mon Mar 16 16:57:59 EST 1998 | Earl Moon
| We have just go another batch of PCB's from our loaders, and some of the boards are severely warped. | The boards are PCI cards and one of the boards is 9mm out at one end. The PCB is 210mm long and 4 layers. | I am wondering if anyone knows what
Electronics Forum | Mon Mar 16 09:07:14 EST 1998 | Justin Medernach
| We have just go another batch of PCB's from our loaders, and some of the boards are severely warped. | The boards are PCI cards and one of the boards is 9mm out at one end. The PCB is 210mm long and 4 layers. | I am wondering if anyone knows what
Electronics Forum | Wed Jun 26 08:53:32 EDT 2002 | davef
We have not done a DOE on board warping. Consider: * How close the board gets to its Tg during the reflow cycle * Amount of copper on each side and the balance between the two * Thickness of the board * Overall length x width * Time at temperature
Electronics Forum | Thu Jun 27 17:24:17 EDT 2002 | Daan Terstegge
Never did a DOE on that, but I think it would be quite difficult to warp a board inside the oven if it was flat when it entered the machine. If there's no center-board support then it's another story, then the board will bend due to it's own weight.
Electronics Forum | Mon Feb 13 23:05:02 EST 2017 | swestheimer
I have been asked a very good question but have not been able to find a good answer. IPC for both PCB and PCBA refer to the X & Y dimensions to measure warp and twist but how would you determine the warp and twist for a round PCB or PCBA?
Electronics Forum | Thu Aug 04 16:34:03 EDT 2005 | bhu
You haven't mentioned whether you are producting only through hole product or if it is mixed technology. What kind of flux (no clean, H2O clean) you are using and whether you performed a first article at part stuffing prior to wave. Generally, you
Electronics Forum | Tue Dec 23 08:31:34 EST 2014 | proceng1
I know the contract rules, but this is idiotic. I did find the 10.2.6 spec already, but I had not looked at the TM-650. I'll check that out, thanks. I also may have found another part that has a better clearance, so I also hope to use these specs
Electronics Forum | Thu Nov 07 10:07:02 EST 2019 | charliedci
Requesting help from anyone with experience in reflowing Te Connect, PN 1565917-4, 200 pin connecter. Pic attached. Cannot get all 200 pins to wet, main suspect is slight PCB warping during reflow. Have adjusted reflow profile. A 2.75 inch long SMT c
Electronics Forum | Thu Jul 22 05:00:45 EDT 1999 | George Verboven
| I have pcb's in which i am experiencing warping. | the boards are 12.8125" on a diagonal measurement. | they are out approximatley .010". | the boards are combination thru-hole,smt, they also have 3ounce copper.what is acceptable,and what is the pr
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830