Electronics Forum | Thu Jun 20 10:48:56 EDT 2002 | Hussman69
When you ask for data in terms of rework, do you want reflow solder yields versus wave solder yields? Or do you want repair data from each process, or yield data that shows actual glue defects from screen printing versus solder paste screen printing
Electronics Forum | Thu Jul 18 08:54:49 EDT 2002 | Mark S.
How do you capture the workmanship details on a "per joint" basis? I have recently implimented first pass yield in SMT but it is based on the whole part and not the number of joints. And yield is calculated by PCB failure rate..a PCB with a solder b
Electronics Forum | Thu Jan 28 15:08:32 EST 2010 | jamyboy
Hello All, Well we have a critical PCB assembly with 30 layers being produced by DDI. We just received word from the PCB shop that this unit only yielded 30% or basically 70% failed. Should we keep the 30% yield or have the shop rebuild al
Electronics Forum | Thu Jul 29 11:34:27 EDT 1999 | Justin Medernach
| | | | | | Presently protos of micro-bgas (80i/o) pitch .030/.031 | | | | | | 12BGA per assembly | | | | | | | | | | | | The board is a (.062, 4 layers) FR-4 using Dry film | | | | | | Pads .014inch | | | | | | Vias within footprint .020inch | | |
Electronics Forum | Thu Jul 29 15:29:30 EDT 1999 | Earl Moon
| | | | | | | Presently protos of micro-bgas (80i/o) pitch .030/.031 | | | | | | | 12BGA per assembly | | | | | | | | | | | | | | The board is a (.062, 4 layers) FR-4 using Dry film | | | | | | | Pads .014inch | | | | | | | Vias within footprint .02
Electronics Forum | Wed Aug 24 21:57:45 EDT 2005 | adeline_ko
The blistering is around the plugging via. I can forward you the pic. For the plugging process, I'm not too sure how they plug. What is the correct practise for the plugging via. Now, what they did is. They will do a tenting process for both side.
Electronics Forum | Fri Oct 10 16:23:59 EDT 2014 | dilogic
First, plug all holes with nozzles or plugs. Then use I/O diagnostics to fire changer up and activate vacuum. Then try to remove each of the nozzles and see if the vacuumm holds. If it does, check vacuum detector switch (mounted on changer side). The
Electronics Forum | Thu Jun 08 09:26:26 EDT 2023 | frankchan
placement> (curing)> reflow soldering> cleaning> inspection> rework SMT production process Surface mount process a. Single-sided assembly: (All surface-mount components are on one side of the PCB) Incoming inspection-solder paste stirring-screen prin
Electronics Forum | Mon Mar 04 11:08:56 EST 2002 | Matt Kehoe
We have a customer that desires to have their via holes plugged with solder after assembly. Is it possible to add the via holes to the stencil and print paste into them and expect them to plug? If so, how much paste? One to one on the stencil opening
Electronics Forum | Mon Jun 13 20:35:22 EDT 2005 | Marcel
I'm looking for the pin out of the cable between monitor ( CRX 1500 F ) and the MCS-16. On the monitor side , it's a Centronic 36 pin plug. On the MSC side it's a standard DB 25 plug. Thanks for your time
WINTECH provides new/used/pre-owned SMT, AI & PCB Assembly (PCBA) equipment of various brands. Also supply service, modification & original or local-made spare parts. We are also an appointed agent for well-known brands.
Equipment Dealer / Broker / Auctions
NO. 1 LORONG SAGA JAYA 6
PERAI, Malaysia
Phone: 6043809899