Electronics Forum | Tue Jul 24 12:34:25 EDT 2007 | jaimebc
Hey Real Chunks, my question was legit, don't use my name to take a shot at someone else.
Electronics Forum | Tue Jul 24 15:13:24 EDT 2007 | adlsmt
I have been using the Heraus paste for almost ten years. At the time we picked it, it and Loctite seemed like the only options. It was a lot less $$ than Loctite. Is there a noticable difference in performance? I think the Loctite was about 2X the pr
Electronics Forum | Thu Jul 26 08:39:16 EDT 2007 | d0min0
since 1999 we use Heraeus PD944, in time we tested Loctite also but had some issues with it - or with our machine specialist :)) we dispense with Fuji CP (2 , 3 & 4) it only creates problems when its on the solder pads ;-) best wishes
Electronics Forum | Thu Jul 06 02:08:27 EDT 2000 | Ralph Landry
I need to build a couple of prototype SMT boards and need some recomendations on some adhesive or epoxy to use to hold the parts down prior to hot air soldering. I find that some parts want to skip across the board when heated, or they want to walk
Electronics Forum | Thu Jul 06 07:30:46 EDT 2000 | John
Ralph, Typically our co-op students put down solder paste with a syringe, place the parts on the paste with tweezers, and then reflow the paste with a hot air pencil. This works pretty well when they are hand building prototypes. You can probably
Electronics Forum | Thu Jul 19 18:03:14 EDT 2007 | dwanzek
Wait...stop! Some adhesives will void when cured... some common branks... maybe already mentioned. Heraeus PD955 will minimize voiding when curing the adhesive. Voiding can have devestating consequences....learned from experience. Another key is kee
Electronics Forum | Wed Sep 05 10:36:47 EDT 2007 | dwanzek
Hope you found an adhesive that works for you Dback. Thought I felt sharp pain in my back for awhile as did not follow up on this string. Then again, a response may prolong the pain, oh well figured a need for accurate information. FYI for RealHuss
Electronics Forum | Tue Jul 17 12:32:10 EDT 2007 | jaimebc
Actually, you just decribed what I am wearing, down to the hair! Are you a co-worker? Anyway... Without going into details, that is the process that we currently have and will continue to use, because it has worked for our application. So, with th
Electronics Forum | Fri Jul 20 13:15:15 EDT 2007 | hussman
What? D Wanzek works for Heraus?!?!? Jeez, these f*cking snakes in the grass around this site are just too much. I guess I should've realized it when he started blathering about the product, it's part name, spec and the whole bunch of crap sales
Electronics Forum | Wed Oct 14 10:04:02 EDT 1998 | Dr. Kantesh Doss, Siemens Energy & Automation, Inc.
Sanjay: Keys to successful adhesive printing are: 1. Understanding the flow behavior of the adhesive under constant shear stress 2. Stencil design, i.e. stencil aperture opening 3. PWB Footprint 4. Stencil printing parameters Optimizing all these fac
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, China
Phone: 0755-33578694
