Electronics Forum: underfill and keep and out (Page 3 of 7)

New Pick and Place Operation

Electronics Forum | Tue Jan 17 12:25:56 EST 2006 | Cmiller

Pete C, this forum has no value if people do not share thier real world experience. We can all do research on our own. We can all make bad decisions or good decisions based on that research because most of the data we have access to comes from the pe

Re: SMD Inspection and Touch-up

Electronics Forum | Fri Jul 23 23:47:03 EDT 1999 | Scott McKee

There is a practise within the industry of an Inspector inspecting a board, and that same Inspector performing touch-up. My opinion is that the Inspection and Touch-up operations should be separate functions whereby the Inspector is not perform

V-Tek Tape and Reel Machines...

Electronics Forum | Thu Apr 22 13:43:14 EDT 1999 | Steve Gregory

Hey Ya'll! Have any of you ever worked with one of V-Tek's "Economax" tape and reel machines? The biggest thing I'm curious about is the type of cover tape that these machines use. It's something they call P.S.A. (Pressure Sensitive Adhesive)cover t

New Pick and Place Operation

Electronics Forum | Tue Jan 17 05:02:33 EST 2006 | grantp

Hi, I was replying to this thread appearing suddenly. However I have run both machines, and I paid for them myself because I run my own company, and so the choices I made, I personally had to pay for. Also, anyone who's been on this forum for a whi

Re: Flip Chip and lead-free soldering

Electronics Forum | Thu Jul 20 16:15:24 EDT 2000 | Bob Willis

Sorry at the moment I do not have information but as usual I want to get some hands on sessions going. We were doing a flip chip workshop hands on session for Speedline last week in England. We did the theory and then hands on soldering and underfill

Looking for printer and placement machine agency

Electronics Forum | Wed Jun 15 14:51:28 EDT 2005 | russ

Please post in the marketplace, you will have better luck and it will keep all of the sales guys out of the technical forum (no offense intended Harry).

Compressor for Pick and Place line

Electronics Forum | Wed May 20 14:03:53 EDT 2020 | dwl

Buy a dryer to go with your compressor. Compressed air traps a lot of water and you don't want that in your air lines on your P&P machines. Additionally, make sure you keep up with all the preventative maintenance and change out the filters as requir

Multi-part reeling for pick and place

Electronics Forum | Sat Jul 17 10:04:39 EDT 2004 | stefwitt

I think we should shift this issue to the machine suppliers, requesting changes in the machine design, in order to keep at least the jobs of high mix, low volume in this country. We can only compete with low labor cost countries by increasing the lev

iPulse M4e Pick and Place Machine

Electronics Forum | Mon Oct 24 01:19:10 EDT 2005 | darby

Hi Mike, I use variations of both of these machines in a Tenryu FV-7100s and Samsung CP45/CP45Neos. Both have been very good machines - I would find it difficult to split them. I have personal dislikes of both tooling and support systems. I would ta

Re: Tabletop pick and place equipment selection

Electronics Forum | Fri May 28 16:03:10 EDT 1999 | Jeff Sanchez

Has anyone had experience with prototype-scale, table top Placemax and/or Manncorp pick and place equipment? If so, what has been your experience with the machines? Are they reliable? Did they meet all your needs? Which needs didn't they fill?


underfill and keep and out searches for Companies, Equipment, Machines, Suppliers & Information

In-line PCBA Routing Machine Shenzhen ETA

PCB Assembly Supplies - ONLINE STORE
Selective Conformal Coating System

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
PCB Surface Cleanliness

World's Best Reflow Oven Customizable for Unique Applications
Sell Your Used SMT & Test Equipment

ONLINE IPC Training & Certification
PCB Depanelizers

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...