Electronics Forum: rework (Page 267 of 293)

Yo! Who's got a decent used Airvac/Solder fountain for sale?

Electronics Forum | Tue Aug 18 16:48:38 EDT 1998 | Steve Gregory

Hey there ya'll!! I went and looked at the used equipment page here, and I've also looked around at a few other sites to try and find me a used PTH dynamic solder pot...like a Airvac type of unit. It doesn't have to be as fancy as a Airvac, just

Re: Yo! Who's got a decent used Airvac/Solder fountain for sale?

Electronics Forum | Tue Sep 01 23:21:36 EDT 1998 | MIKE

Hey there ya'll!! I went and looked at the used equipment page here, and I've also looked around at a few other sites to try and find me a used PTH dynamic solder pot...like a Airvac type of unit. It doesn't have to be as fancy as a Airvac, j

Re: BGA Repair Problems

Electronics Forum | Wed Aug 12 14:39:09 EDT 1998 | Mike C

Have an SRT w/preheat, 18 layer board all copper, 456 BGA needs to be removed and replaced. The manufacturer is Chip Express and during reflow it warps up or down. Causing either opens or shorts on the corners. I was using gel flux with multiple

Re: Bob Willis Free Advertising

Electronics Forum | Fri Aug 07 02:30:08 EDT 1998 | Bob Willis

No sour grapes, This has gone on too long. I expect no free advertising, nor do I seek it. It is clearly understood Bob is an industry leading consultant. What is not understood, at least by me, how he is allowed to "advertise" so freely on t

Re: Solder Spotting on Gold

Electronics Forum | Thu Aug 06 13:09:57 EDT 1998 | Bob Willis

Bob I have had problems with spotting on gold contacts for many years and have spent many hours working on ways to solve this problem. Once a source of the problem is found and corrected the next month another source will crop up (new operator o

Tape and shunts are good ideas for WS *BUT*...

Electronics Forum | Tue Jul 28 07:02:59 EDT 1998 | smd

Right now we are taping the goldfingers which is effective but also expensive. Also, some tape was leaving yellow marks on the goldfingers. We're trying the so-called goldfinger glove from Steven's Products. It's a very small company (probably one gu

Re: Tape and shunts are good ideas for WS *BUT*...

Electronics Forum | Mon Aug 03 08:29:24 EDT 1998 | Dave F

SMD: Sounds interesting. What is the contact information on Steve? Dave F Right now we are taping the goldfingers which is effective but also expensive. Also, some tape was leaving yellow marks on the goldfingers. We're trying the so-called go

Darn-left out contact info on the goldinger gloves

Electronics Forum | Mon Aug 03 08:23:37 EDT 1998 | smd

Stevens Products (supposedly around since 1937) 128 N. Park St. E. Orange, NJ 07019 Tel 973-672-2140 Contact: Ross Stevens, Jr. They'll take a PO but terms are net 30 Right now we are taping the goldfingers which is effective but also expensive. A

Re: Solder paste with BGAs?

Electronics Forum | Thu Jul 23 11:39:16 EDT 1998 | Russ Miculich

Are you using a HASL board or an organic protection on the pads? This will help determine as to whether paste is necessary or just a very active/tacky flux should be used. Tight process control will also help in the reflow oven. Many users don't wan

Re: Looking for Procedures for SMT repair

Electronics Forum | Fri Jun 19 21:04:21 EDT 1998 | Dennis O'Donnell

I am looking for a quickly obtainable procedure on the repair of SMT boards. I am particularly interested in discrete components, such as capacitors and resistors. I need to know the importance of pre-heating the board and components. Wh


rework searches for Companies, Equipment, Machines, Suppliers & Information