Full Site - : mpm ap forcer hangs (Page 1 of 2)

MPM Vision X Platen with Forcer

MPM Vision X Platen with Forcer

Used SMT Equipment | SMT Equipment

Used working MPM AP25 series vision x-axis platen with forcer. MPM Part #'s 1) Vision X Platen - P1294 2) Assy, Motor Vision X Forcer - 1003647

Macrotron Systems

Camera not parked error on mpm ap 25.

Electronics Forum | Mon Jun 12 23:52:58 EDT 2017 | aemery

Don, either you have a faulty park sensor or much more likely the vision gantry Y axis is not reaching the sensor. Possible issues, one of the two VY drivers cards is failing; one of the VY forcer motors (air bearings) is failing; to much air leakin

MPM spare parts

Electronics Forum | Sat Jul 16 18:24:11 EDT 2016 | aemery

Scratches do not necessarily mean bad! Usually the forcer motor fails before a platen. The motors become weak or don't evenly distribute the supplied air, which causes them to tilt and drive into the platens. Mechanical misalignment of the VY forcer

MPM AP-20 drivers

Electronics Forum | Mon Jul 26 21:56:53 EDT 2004 | pdeuel

The camera is not driven from the motor cards. The camera is attached to what is called a forcer. For the Y axis there are two of them. One is wired backwards from the other. one of the forcers is connected to a flex chanell for the air and electrica

MPM AP25 Print Repeatability Problem

Electronics Forum | Mon Sep 25 12:50:42 EDT 2006 | chris g

Daxman, The diagnostic results didn't look very pretty. Especially on the vision x standard deviation. Any time there is an asterisk, that is a bad thing. The failure number for all axis, excetp theta, is .0002. Could need more air flow to the x

MPM spare parts

Electronics Forum | Tue Aug 16 22:51:06 EDT 2016 | aemery

Sorry I didn't catch your message sooner! 20k is way to much. The odds of you having 3 bad platens and 3 bad forcer motors would be very unlikely, unless the machine was sitting outside or something. If it is a 10 year old AP then I assume it must

MPM AP25Hie Pre Board Stop error

Electronics Forum | Mon Jul 30 17:32:34 EDT 2007 | chrisgriffin

When you teach the "teach boardstop Y" make sure the camera is seeing the leading edge of the board and not too close to the rails. It should calculate the pre-stop position correctly. I assume you have thoroughly checked the sensor. Also check th

Technical problem with MPM-AP-24

Electronics Forum | Thu Nov 11 17:49:11 EST 2004 | pdeuel

We are having a problem with our AP-24x printer. When the vacuum motor spins up we get a 60 hz buzz into the DC drivers for the forcers and the stencle wiper. We also indicate a main power drop from 115 vac to 80 vac. The vacuum motor checks out good

MPM AP25 Print Repeatability Problem

Electronics Forum | Fri Sep 22 14:07:29 EDT 2006 | realchunks

I think Sr is right. Miss prints are prolly a result of your tooling moving the board after the camera looks at the fids. It also could be the camera itself hitting the board from warpped board or tooling raising the board up. It may be the camera

MPM Ultraprint 2000

Electronics Forum | Tue Mar 28 19:28:54 EDT 2017 | aemery

Giao, These style of MPM's use stepper motors, but no feedback like an encoder or a resolver. In other words all axis positions are assumed after "Reset" of the machine. Because of this style of drive system there is the potential for the vision ga


mpm ap forcer hangs searches for Companies, Equipment, Machines, Suppliers & Information

NPM D3 Machine

Best Reflow Oven
Sell Used SMT & Test Equipment

PCB Assembly Supplies - ONLINE STORE
High Throughput Reflow Oven

ONLINE IPC Training & Certification
PCB Depanelizers

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...