Electronics Forum: matrix tray changer (Page 4 of 15)

Matrix Tray Feeders

Electronics Forum | Fri Oct 22 17:15:58 EDT 1999 | Parvez Patel

Hi, I am trying to locate any vendor who can supply me some 28 mil * 28 mil matrix tray feeders for test component storage Thanks Parvez Patel SMT Lab UIC - Binghamton - New York

Mydata TP11 1995

Electronics Forum | Tue Apr 05 12:45:01 EDT 2005 | cyber_wolf

Make sure your matrix tray is up high enough. The components in the matrix tray should be at least at board level. Also check your component height in the package list. If all that is OK then, check those Z locks I spoke of earlier.

Samsung CP45 Neo Matrix Tray Holder

Electronics Forum | Thu Oct 29 10:29:13 EDT 2009 | soporto77

Hi, I'd like to know where i can find a Matrix Tray holder cheap (Pick and Place Samsung CP45 Neo) Thank you for your help

Matrix Trays

Electronics Forum | Wed Oct 16 20:24:45 EDT 2002 | kenbliss

Hi ChrisN Have you talked with your supplier that is sending the components into your plant in trays. They are putting the components into the trays or their source is. One of them should be able to give you credit for each returned tray. Ken Bli

Matrix Tray Setup

Electronics Forum | Thu Dec 31 12:32:29 EST 2009 | vetteboy86

Thank you very much for the input. I figured out my problem to be that once I defined the tray, I did not changeover the table top just as Bob said. I'm good to go now, I think anyways. I was so used to the IQ feeders, changing over the matrix tray

Quad IVc AutoProgram

Electronics Forum | Thu Apr 04 07:09:39 EDT 2013 | leemeyer

Autoprogram will use whatever tape feeder width is defined for that component (SMD type)and will adjust the pickup accordingly. Autoprogram will not tell you where to place Vibs and Matrix trays. You need to decide where to mount the holders. Then m

Matrix Tray

Electronics Forum | Wed Dec 21 08:30:13 EST 2005 | jax

"aj" you should find your way to a training class. The measurement is from the zero point of the tray feeder( almost always the feeder slot pin giude that the center guide of the tray holder hits...located in the machine ). It is not the same as nest

Using Stripfeeders on MyData Tray Wagons

Electronics Forum | Tue Jun 24 11:58:55 EDT 2014 | markhoch

We had both a MY15 and a TP11 both with tray wagons and we taped strips to the tray wagon all the time with great success. we used double sided tape, sometimes with magnets, and then created "trays" as if the tape strip was a matrix tray. (1 x 10,15

Matrix Tray Holder

Electronics Forum | Mon May 14 13:01:21 EDT 2001 | Charlie

We had two 51 space trays. One was modified by machine shop to hold two waffle trays. We bought a 31 space tray thinking it would hold one tray, it doesn't. We modified it to hold one tray. We than learned, from tech support, that a 31 space base sho

Re: Matrix Trays

Electronics Forum | Thu Apr 06 10:50:20 EDT 2000 | John Thorup

As Ioan says,These components usually come in tubes rather than trays. I can understand why you might want to do this because I have one very low volume but complicated board that has seven programmable PLCCs that I just don't have room for on the m


matrix tray changer searches for Companies, Equipment, Machines, Suppliers & Information

Dual Lane Reflow Oven

Best Reflow Oven
Fluid Dispense Pump Integration

Reflow Oven
RETROFIT for More Effective Dispensing

High Throughput Reflow Oven
ACI Technologies, Inc. - Counterfeit Component - Solder Techniques for Electronic Assemblies - BGA Inspection, Rework and Repair

fully automatic component storage