Electronics Forum: nozzle and magnetization (Page 4 of 18)

Pick and Place drops nozzles

Electronics Forum | Tue Jul 05 10:27:34 EDT 2005 | GEB

The nozzles are brand new too (got them friday). 08MPF (0.08") is their part number. I tried using the air kiss feature in the setup mode and found that it blew the nozzle off the nozzle holder, not sure if this is ment to happen in this mode, but t

Universal GSM and 0402/0201 Placement

Electronics Forum | Mon Jan 19 09:07:45 EST 2015 | cotinc01

We can offer several nozzles to assist with the placement of 0402/0201 components in the four-spindle head. We offer the 06MPF along with custom ceramic tipped nozzles. Most of our standard nozzles for this head type are less than $125.00 each. Chec

Pick and Place drops nozzles

Electronics Forum | Thu Jul 07 07:27:10 EDT 2005 | buchi79

Are you buying nozzles from UIC or other vendor? By the way, what is the component you rejecting? Is it happening to random component or specific one?

Pick and Place drops nozzles

Electronics Forum | Wed Jul 20 22:46:41 EDT 2005 | nozzles

we can supply nozzle for varies machine brand,such as fuji,sanyo and so on. welcome to inquiry that!thanks vera http://www.hkenterprise.com/szcomfaje tel:86-755-28091605 ext.805 eskimy1001@gmail.com

Pick and Place drops nozzles

Electronics Forum | Wed Jul 27 12:50:59 EDT 2005 | mnguyen

You may want to look at which spindle that is dropping the nozzle and check the O-ring on the spindle head. It's probably bad, cracked, or broken. Replace it and that will fix it

Universal GSM and 0402/0201 Placement

Electronics Forum | Fri Jan 16 16:34:01 EST 2015 | rgduval

It's a four-spindle head. I've already learned the joys of the size of the nozzles...on a job that had an 0603 cap a bit too close to an SOIC. The first panel ran, and the cap placed after the IC...and I had parts everywhere. Got it figured out an

Pick and Place drops nozzles

Electronics Forum | Tue Jul 05 16:29:27 EDT 2005 | stepheniii

The air kiss is to replace the vacuum with air so the part will drop off the nozzle. Every machine I've seen with Air kiss, uses it when discarding a part as well as when placing a part. The air kiss should not be strong enough to blow the nozzle off

Pick and Place drops nozzles

Electronics Forum | Mon Jul 04 11:32:44 EDT 2005 | geb

One of my Universal GSM (1995/ 1996 model) pick and place machines has recently started to drop the nozzle on the reject belt when dropping off a rejected component. I have tried replacing the nozzel holders on the ends of the spindles but with no im

CSM-84 pick and place machine.

Electronics Forum | Sun Feb 13 16:28:00 EST 2011 | tpappano

Does nozzle #1 lower at all when it should pick up a part or is it just staying in the fully up position? If it does come down, but not quite far enough to contact the part, there are adjusting nuts on top of the head that set the lower limit for no

CSM-84 pick and place machine.

Electronics Forum | Sat Feb 12 13:19:27 EST 2011 | tpappano

A simple trick I read either here or on another P&P forum is to use "Silly Putty". Place a small thin spot of Silly Putty on the top of the front conveyor rail, and put the machine in "manual" mode. Steer head #1 over the putty and lower it, leavin


nozzle and magnetization searches for Companies, Equipment, Machines, Suppliers & Information

Selective soldering solutions with Jade soldering machine

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
Selective soldering solutions with Jade soldering machine

Benchtop Fluid Dispenser
Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

Best Reflow Oven
PCB separator

Find a wide selection of nozzles, solder materials, storage solutions and more at SALESCON