Electronics Forum | Wed Feb 01 02:21:26 EST 2017 | rob
80 micrometres (0.08mm) or 80 mil (2mm)? Smallest I've seen reliably printed is around 0.2mm x 0.4mm (01005 pad) and 0.2mm x 0.2mm CSP pad, not seen anything dispensed below 0.35ish, but we are not cutting edge.
Electronics Forum | Mon May 03 15:16:01 EDT 2021 | capse
Thin FR4 can be routed with a CO2 laser with high quality results, the edge is precise and free of slag. The process is extremely low stress. If the edges are straight you can consider sawing. 0.4mm (0.016") FR4 can be laser routed and sawn at spee
Electronics Forum | Thu Oct 11 22:25:50 EDT 2001 | davef
Bruce I�m with yall. Designers and fabricators say �pins�. You say: * BGA pins are 1mm [0.039�] pitch. * BGA pads are 0.4mm [0.0157�] diameter. * BGA pins are 0.6 mm [0.024�] side-to-side. * Board thickness is ~0.4 mm [0.015�] First, as you can
Electronics Forum | Tue May 25 12:59:37 EDT 2004 | gregp
Mils to MM is actaully English to metric. 1 mil is equal to 1 thousandth of an inch (0.001")or 0.0254mm so... 12mil pitch qfp is 0.012" or 0.3mm 15mil pitch qfp is 0.015" or 0.4mm 20mil pitch qfp is 0.020" or 0.5mm (Numbers are rounded)
Electronics Forum | Wed May 03 10:58:35 EDT 2006 | rlackey
Hi has anyone noticed any issues with reduced component lead diameters on through hole resistors? All the volume manufacturers have or are in the process of reducing the lead diameters from 0.6mm to 0.4mm due to the huge increase in copper prices o
Electronics Forum | Thu Jun 19 21:39:31 EDT 2008 | mika
Hi, we used to have a RoHS package with uBGA 380 Solder ball's 0.8 mm pitch approx 15x15 mm, bump size is 0.4mm on a 0.33mm pad. Suddenly we need to use another vendor for various reasons. However, the new bump size is 0.45mm according to specs and t
Electronics Forum | Thu Dec 14 22:28:38 EST 2006 | Tony
Hi, where can I find info about how to make the pad design to work for VSSOP48 0.4 mm Pitch & TSSOP56 0.5 mm pitch components? I should also mention that we are working in a project that this 14 layers High-Frequency RoHS board is included. The pad c
Electronics Forum | Wed Sep 12 03:52:45 EDT 2018 | shascoet29
Hi, Is the IPC-A-610 applicable to CSP assemblies? Especially regarding the solder ball to solder ball distance versus the minimum electrical clearance for assembly(0.13mm/IPC-A-610). With a 0.4mm pitch component and 260 microns diameters balls, thi
Electronics Forum | Tue Jan 30 21:14:26 EST 2001 | davef
Suggestions are: * Limit pad width to 0.008" [0.2mm] * Use IPC-7525 Stencil Design Guidelines * Avoid Type 4 pastes, if you can * Slow down your print head to 0.63"/sec [16 mm/sec] * Consider the suggestions on printing by rpereira in the past
Electronics Forum | Fri Mar 03 06:41:09 EST 2000 | jacqueline coia
I have tried the IPC calculator and they do not have this type of component registered. When trying to select 'other' on menu, no connection can be made. The polarity if the QFP has not been decided yet (pre-PCB design) the pitch size of the componen