Electronics Forum | Thu Aug 12 14:17:19 EDT 2010 | mikesewell
You might reduce your panel size, cut it in half and rotate to better utilize your edge clamping/board supports. Tape off your current stencil and see if it improves the print. A new stencil and a little extra handling may be cheaper than tooling.
Electronics Forum | Sun Nov 01 23:34:25 EST 2009 | 89jeong
Hello Julie Yr supplier is saying that these boards meet the requirement of IPC-A-610. I think that you need to check this requirements at least. But, it does dot mean that these are acceptable. Thanks.
Electronics Forum | Tue Aug 04 12:55:10 EDT 2015 | davef
Check these threads: * http://www.smtnet.com/Forums/index.cfm?fuseaction=view_thread&CFApp=1&Thread_ID=16481Message67330 * http://www.smtnet.com/Forums/index.cfm?fuseaction=view_thread&Thread_ID=10127 BR ... davef
Electronics Forum | Wed Aug 19 03:24:49 EDT 2015 | pcbman
I ordered few times of prototyping gold plating > pcb from China. How to i differentiate they are > ENIG or Flash gold? Hi,Friend , this is very easy to distinguish the ENIG and gold plating pcb, you can stratch the solder mask off and see the co
Electronics Forum | Thu Oct 23 23:38:48 EDT 2008 | pathakvj
We have 8 layer HASL PCB. We saw molten solder blobs / balls on op side of assembled PCB. (to check, if this was a bare board problem), We passed bare board as received thru, SMT reflow oven and saw solder balls on top side of board. What could be th
Electronics Forum | Fri Oct 24 06:55:48 EDT 2008 | clampron
Good Morning WS, If you experieced the solder balls after reflow of a bare board through the oven, then the source of the solder is either the oven or the board. I have had boards with untented via's that were HASL'd that had entrapped solder and fl
Electronics Forum | Sun Nov 01 01:33:52 EST 2009 | isd_jwendell
Just my opinion: Top pic - Solder mask registration WAY too far off, without a doubt I would reject. Bottom pic - I would worry that there was/is a contamination that caused the poor looking mask. This may be cosmetic only, but unknown. I would rej
Electronics Forum | Wed May 04 10:42:55 EDT 2005 | nice90
Handling a PCB 1. Check your ESD slippers and ESD Strap first before entering the SMT production line 2. A PCB manufactred over 90 days must be stored first on the baking Oven before Production 3. Temperature on the Baking oven must be 125plus and m
Electronics Forum | Mon Jul 12 05:03:30 EDT 2004 | itamar
hello ! my name is itamar and i need information about pcb laser marking machines. my knowledge in this field is limited and i would be grateful to know the important parameters that one should check before buying such a machine. i got several propos
Electronics Forum | Mon Nov 02 07:16:47 EST 2009 | umar
Base on the top picture condition, seems like the boards condition is a lot with solder splash or solder ball which is per IPC-610 is under reject (under 5.6.2)for class 3 product. While the picture 2 is showing those the solder resist is not melt pr
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830