Electronics Forum: thermal pad (Page 6 of 49)

Heat Sink for QFP

Electronics Forum | Tue Mar 28 08:29:04 EST 2006 | davef

Pad design - Standard IPC 20 pitch QFP Thermal pad design - Layout the thermal pad 0mm to 0.15mm larger per side (0mm to 0.30mm larger overall) than the exposed die pad on the package. �Larger than�, as opposed to the same size, is preferred. Obvio

28 pin QFN Pads.

Electronics Forum | Thu Sep 16 17:56:48 EDT 2010 | asksmt

Ok Thanks, i have reduced thermal pad size by 4.5 mils on top and bottom part of this footprint where the problem was occuring, so now the clearance between thermal pad and lead pads are 12 mils instead of 7.5 mils on two sides. (i kept the signal pa

IC Solder Voiding

Electronics Forum | Tue Nov 26 09:05:48 EST 2019 | scotceltic

Thank you for the response. Nothing in the datasheet referring to a percentage of thermal pad coverage. I am thinking along the same lines. We are not failing any thermal or functional testing as is so am thinking there is no problem here except m

28 pin QFN Pads.

Electronics Forum | Tue Sep 14 17:06:25 EDT 2010 | asksmt

Hi All, I have designed 4 Layer PCB with one 28 pin QFN PKG. I have got complaint from Production that the pads which connected to thermal pads (gnd) thru trace is bridging with solder and because of this bridge, pins are not getting soldered prope

Best way to ensure max solder load on SOIC w Thermal Pad

Electronics Forum | Tue Nov 09 04:21:11 EST 2010 | bising

Hi SMT World, I am facing a technical challenge related to an SOIC 14lds with thermal pad on it's belly that needs to be soldered onto PCB, together with leads. It is a 50 per board, expected 80% solder load on every one. We have some units without

LGA... where to start?

Electronics Forum | Fri May 09 08:27:35 EDT 2014 | emeto

REduction of center pad is the key as well as the stencil thickness. Having too big opening on your stencil will sometimes lift the part from the pads. Always try to make windowpane and shoot for about 60% of the thermal pad to be covered as start p

SMD module moving during reflow

Electronics Forum | Fri Jun 21 02:11:27 EDT 2019 | alanyang

Many aspects cause such problem, stencil windows and thickness, thermal pad and crowded PTH vias on PCB, the castellated pad size and pcb pad size. Do you have picture for reference?

QFN PCB Pad no Drain Hole

Electronics Forum | Sat May 18 10:21:09 EDT 2013 | davef

isd.jww: Comments are: * Current thinking has flux volatiles being the major contributor to voiding, not scavanging by via * I have no reason to think that 0.3mm via won't gladly accept solder. Plug them, if that's a concern. * If your concern is ina

QFN84 Solder Printing Issue (QFN with Inner LGA Pad)

Electronics Forum | Sat Dec 02 10:23:47 EST 2017 | tomh

Have you ever heard of "Solder Mask Defined Thermal Pads"? I wrote a short blurb on this here - https://www.pcblibraries.com/forum/ipc7093a-btc-qfn-solder-mask-defined-thermal-pad_topic2154.html This technology saves fabrication costs by not havi

Voids with LGAs

Electronics Forum | Fri Jan 18 14:39:07 EST 2013 | davef

Main issues with LGA voiding are: * Design * Material selection * Thermal recipe For design, loo here http://blogs.smtnet.com/smt/other/qfn-btc-design-guidelines-thermal-pads-etc/ BR, davef


thermal pad searches for Companies, Equipment, Machines, Suppliers & Information