Electronics Forum | Fri Jun 18 15:37:44 EDT 2010 | remullis
One thing I have run into when placing cap's flush to the board is blow holes due to the plastic sheathing used around the cap. It would form a gasket going through wave and exhaust out of the holes therefore blowing the solder out with it. This cap
Electronics Forum | Tue Aug 14 10:01:32 EDT 2007 | gmoritz
I have posted earlier on a UIC Radial inserter machine. We have the machine running after repair of the CnC head. However, I now have a process problem with a board that has 256x3 LED parts (768 LEDs in three colors) where only 50% of the LEDs can b
Electronics Forum | Thu Jun 20 19:27:28 EDT 2002 | surinder
Hi Dave, I am agree with you,but one of my customer want to know the difference in terms of rework/Quality,if we go for Glue process in place of solder paste and want to see some data We have board ,which have Through hole components and smt comp. on
Electronics Forum | Mon Sep 06 09:55:52 EDT 2004 | Joe O.B.
Hi, We're going to migrate our boards from through-hole to SMT, and I'm dealing with the PCB layout. I've found a lot of references for fiducial marks but none of them states if components can be placed beyond the marks limits or only within the are
Electronics Forum | Tue Jun 11 06:24:07 EDT 2013 | trottmann
thanks. 1. yes, i understand this requires SMT > assembly. > > 2. For bigger components (USB and > phone jack), how can these be placed > automatically on PCB? The manual process will be > slow. Hello, Use "THR Through-Hole-Reflow" also calle
Electronics Forum | Thu Mar 25 14:00:45 EST 1999 | Bob Willis
| Rob, | | We are also using intrusive reflow to simultaneously process SMT and Thru-hole components. Our arrangement goes as follows: | | - Screen print solder paste to the single sided PCB using 0.008" laser cut stencil. | - Apply adhesive dots
Electronics Forum | Tue Aug 14 16:26:21 EDT 2007 | slthomas
So it's a C-n-C clearance issue? Could you go with the other cutnclinch unit...which ever you have, get the other one (one's right angled, one's offset at 45�)? Yeah, I know, they're not cheap. Other than that, hand place some of the SMT in chip bon
Electronics Forum | Sun Aug 13 00:15:58 EDT 2017 | deanm
We manufacture low volume, high reliability assemblies (class 3) that are conformal coated. Up until now we have been cleaning after SMT, then after through hole, then immediately prior to coating with test, formal inspection, etc. between cleaning p
Electronics Forum | Tue Mar 23 04:07:44 EST 1999 | Scott Davies
Rob, We are also using intrusive reflow to simultaneously process SMT and Thru-hole components. Our arrangement goes as follows: - Screen print solder paste to the single sided PCB using 0.008" laser cut stencil. - Apply adhesive dots to selected
Electronics Forum | Thu Jul 27 08:02:55 EDT 2000 | Jason
Hello once again! I am having a problem with a 24 pin connector bridging on the wave. We use very similar connectors on other PCB with zero problems. This connector bridges in the same place on the same pins. It forms like a little block of four
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, China
Phone: 0755-33578694