Electronics Forum | Thu Jul 18 12:44:24 EDT 2013 | ericrr
after checking two computers, did not find it. However after using "google" found it in a flash. (less than 0.22 seconds) using a spreadsheet. how about this for resistor & capacitors with 4mm pitch, all measurements in millimeters. cell A1 "input
Electronics Forum | Mon May 21 20:55:19 EDT 2001 | dougk
We have both CP 4/2's and 4/3. We're also running Siemens S20's & F4's. The 4/3's vision is more temperamental and slightly harder to program. Machine startup and nozzle centering takes longer, but placement time is slightly better. Honestly, for wha
Electronics Forum | Thu Oct 14 09:01:59 EDT 1999 | Bruce
Why not to use an MCS30: Hardware is proprietary, OS-9 format, expensive to fix or replace, support, slow, RS-232 or ethernet hookup for CAD download, flat file format. F4G: PC is purchased by you, WindowsNT 4.0, inexpensive to fix or replace, supp
Electronics Forum | Wed Feb 10 02:09:07 EST 1999 | zeek
| Any thoughts from FUJI users on the likes and dislikes (pros and cons) of MCS vs. F4G , and vice versa? | | Likewise, are there any "FujiCAM" users out there who would like to comment as well? | | Thanks. | We have had some experience with both
Electronics Forum | Wed Feb 10 02:10:39 EST 1999 | zeek
| Any thoughts from FUJI users on the likes and dislikes (pros and cons) of MCS vs. F4G , and vice versa? | | Likewise, are there any "FujiCAM" users out there who would like to comment as well? | | Thanks. | We have had some experience with both
Electronics Forum | Thu Sep 10 09:21:27 EDT 1998 | Y.F. Michael Kou
| We are using PCBs of CEM3 Material with bare copper fiducials. The whole | board is of bare copper with a lacquer coating (Coats brother S2974). | The fiducials are of 1 mm diameter bare copper. we use Panasert MV2F as | well as Fuji CP4-3. In bo
Electronics Forum | Fri Oct 04 01:18:27 EDT 2002 | sarge
1.5. Width >= 4-5 Particle Diameters. Use the smallest opening to determine this. Using dimension of the smallest aperture width, you should be able to fit minimum of 4-5 solder balls side by side into the opening. For 0201 design, -400 mesh (type
Electronics Forum | Mon Apr 12 15:52:12 EDT 2004 | wgaffubar
I am using Indium 92J type 4 solder paste due to a BGA site with .008" pads and stencil opening of .009" square and .005" stencil thickness. When I try the type 3 we get insuffecient print. The aspect ratio tells me that I should be using a type 4. T
Electronics Forum | Tue May 01 13:52:51 EDT 2007 | jasont
plz advise if the below feeders are compatible on CSM 46/60 (are they downwards compatible?); 1. Philips series FV-84-xxxxxC, model PA2903/70 (2,4 pitch, 8mm) QTY=29 2. Philips series FV-82-7-xxxxD, model PA2903/73 0603-type (2,4 pitch, 8mm
Electronics Forum | Fri Feb 15 15:55:58 EST 2008 | pjc
This is from the OmniFlo 5 Engineering data sheet: EXHAUST SPECIFICATIONS: STANDARD AIR OPERATION: - Load-end: 150 cfm (255 m3/hr) at the 4� (102 mm) stack (minimum requirement) - Unload-end: 300 cfm (510 m3/hr) at the 4� (102 mm) stack (minimum req