Electronics Forum: smt ebso connectors (Page 7 of 34)

AMP SMT Connector

Electronics Forum | Tue Apr 13 08:38:15 EDT 2004 | Steve L

The temp. was measured at the leads. We also did dipping test on those connectors, it turned out the solderablity of the pins was awful. We're now checking it with the supplier. Thank you all for the input.

Harwin PC/104 Connectors

Electronics Forum | Thu Nov 05 20:19:05 EST 2009 | martinwuest

I would switch to Teka PC104 solder bearing lead connectors. You can reflow them along with your SMT and eliminate hand soldering. I've had a lot of experience with them and they work great. http://www.tekais.com/pc104.asp Steve

SMT fine picth connector lead oxidize-Throw out rate too high!

Electronics Forum | Thu Sep 05 23:32:29 EDT 2013 | winson16

This connector was designed with gold flash plating and the lead's surface was become dull and some black mark was observed on the contact surface.

wave solder bridges

Electronics Forum | Thu Jul 27 08:02:55 EDT 2000 | Jason

Hello once again! I am having a problem with a 24 pin connector bridging on the wave. We use very similar connectors on other PCB with zero problems. This connector bridges in the same place on the same pins. It forms like a little block of four

SMT Connectors: Corner legs lifts.

Electronics Forum | Thu Jan 16 10:07:12 EST 2020 | davef

Hej back at ya Your connectors could be warping during reflow. Find out by putting a connector on a hot plate and increasing the temperature. If so, you might get away with a simple fix of rotating the board 90* on your reflow oven conveyor. If you

Connector solderability

Electronics Forum | Tue Nov 05 16:41:53 EST 2002 | Ray M

This one's got me stumped, so I thought I'd throw it out for discussion: I have a 20 pin SMT ribbon connector by Molex that I've been using for about a year without problem, but recently things aren't looking so good. The solder is pulled up off of

Re: SMT handplacements

Electronics Forum | Tue May 16 04:52:59 EDT 2000 | Eric

What type of component you are handling. Connector or IC.

SMT Connector, Placement Issues

Electronics Forum | Fri Oct 03 11:01:43 EDT 2008 | hussman

Change your board to bigger holes.

SMT Samtec dual edge connector assembly help

Electronics Forum | Wed Jan 08 16:27:11 EST 2020 | rmitchell

We have a PCB with the dual sided connector that slides on from the edge and has leads on the top and bottom sides of the PCB. It has 20 leads on each side of the PCB with with about .8mm pitch. The PCB also has a gold grounding strip on the edge fo

SMT Assembly Line

Electronics Forum | Thu Jun 08 05:04:57 EDT 2006 | grantp

Hi, The only problem with wave is loading the parts, and SMT is lower cost, and faster. We use wave for connectors through, and it works great, as it's fast when there is lots of connectors. I think he's panelizing, so he should be cool on doing m


smt ebso connectors searches for Companies, Equipment, Machines, Suppliers & Information

KingFei SMT Tech
KingFei SMT Tech

Main Products: 1, Original new and Original Used SMT/AI Spare Parts. 2, SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3, Maintenace and Repair Service Pre-Sales Service Provide details ab

Service Provider / OEM / Manufacturer's Rep / Equipment Dealer / Broker

FengHuang,Fuyong
Shenzhen, China

Phone: 0755-33578694

Online IPC Training & Certification

PCB Assembly Supplies - ONLINE STORE
Selective Conformal Coating System

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
https://pages.zestron.com/zestron-analytical-support-services

World's Best Reflow Oven Customizable for Unique Applications
High Throughput Reflow Oven

ONLINE IPC Training & Certification
PCB Depanelizers

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...