Electronics Forum: okay (Page 8 of 30)

Need help for setting up an assembly line

Electronics Forum | Thu Jun 22 08:49:10 EDT 2006 | russ

Okay I was not thinking of the Suzuki, So I would not have any input there. Zones to me does not include the cooling, I also do not count the top and bottom individually as zones. So to me an 8 zone oven would have 16 heaters that you could set, 8

Selective Solder Flux Issue

Electronics Forum | Thu Aug 17 15:13:41 EDT 2006 | samir

I hear Pillarhouse is the "Yugo" of Select soldering! :) Chunks et al is correct that if the innards of the fluxing system are made of non-corrosive mat'ls, you should be okay. I used to deal with the original AT&T Spray fluxers and their spray no

yellow residue

Electronics Forum | Tue Aug 22 18:15:50 EDT 2006 | russ

okay so both the 2005 formulas from interflux are clear alchol based fluxes. Yellow res huh? In looking at the temps here, I would say you might be too hot at both preheat and solder temp. You may be burning flux. How long is dwell time over wave

Soldering Iron Questions

Electronics Forum | Thu Nov 02 18:13:22 EST 2006 | russ

WE are also going through tips left and right as well with the lead free, thats why it is so environmently friendly you know!!! 10 times the amount of tips now going into trash!! okay back on track here you may wantto try some of the other MFGRS

TNT-A capacitors placement problem at CP-6

Electronics Forum | Tue Jan 02 02:30:18 EST 2007 | _____

Ahh yes, 254. Don't give up on the other vision types. 254 can give you skewing as well. Your width and height are awfull close. Even with the 0.5 tolerance it is using the tolerance and saying that it is OKAY. Maybe what you measure is 1.8mm for wit

MPM AP25/HiE, side snuggers

Electronics Forum | Mon Mar 05 14:44:51 EST 2007 | daxman

Hey, I've seen a lot of AP25's with snuggers. I don't know if they all came with the pneumatics or not..but if you have the snugger reg. guage, just underneath the Z table, you should be okay. The fellas at goppm (www.goppm.com) have a lot of knowl

Printer

Electronics Forum | Thu Jun 26 19:38:35 EDT 2008 | chris

Ouch, that hurts Harry. I think you just called me an ass. Okay, I will revise...If you pay less than 15k I wouldn't trust it. Also, if buying used ask for warranty and tech support. I do think MPM is better than DEK. Actually, I'm positive i

DEK265GSX >>>motor commumincation error

Electronics Forum | Thu Sep 25 09:56:23 EDT 2008 | mysmt

Hello, we are using DEK265gsx printers, at the minute ARCOM unit is not communicating with motor control cards 0,1,2,3 in Y1 enclosure. Checked CPU & RS232/485 cards from other DEK265, found okay. Any help will be appreciated. Mysmt

0402 PARTS

Electronics Forum | Thu Jul 02 10:52:45 EDT 2009 | dyoungquist

For 0402s we use type 3 paste. We have .006 and .005 stencils. The .006 works okay but .005 seems to give us slightly better results. We use a 1:1 ratio for the aperture to match the pad, round pad not needed. With accurate placement and a correc

SAC305 soldering to 58Bi/42Sn

Electronics Forum | Tue Nov 24 11:44:12 EST 2009 | mikesewell

I think you're okay reworking with SAC305 but rework with SnPb will result in a SnPbBi alloy with a lowered melting point that may pose reliability concerns. As far as suitability of 58Bi42Sn goes - depends on your requirements.


okay searches for Companies, Equipment, Machines, Suppliers & Information