Electronics Forum: qsv-1 (Page 8 of 9)

Quad QSV-1

Electronics Forum | Tue Nov 25 08:36:32 EST 2014 | bobpan

Tep stands for the transport card. The board is located in the front bottom left of the machine and should be by itself and have green and red leds lit on the top of it. I would try to reseat the card and then try to reboot the machine. If the proble

Quad qsv1 plus

Electronics Forum | Mon Jan 20 03:50:37 EST 2020 | falconex_technician

Hi, my company bough second hand pick and place as our second machine. After first transport after start just when initializing, It's showing problem with Z calibration. After second position setup and connect again after month, now showing &

Quad QSV-1 - Several TEP1 faults during Startup

Electronics Forum | Thu Aug 08 11:04:48 EDT 2019 | btfonseca

Hi everyone, I was recently trying to troubleshoot a bad floppy driver on our QSV-1, which actually worked, I was able to read floppy drives but for some reason it all went downhill when one of the green LED's turned off and another red LED turned on

Placement Equipment

Electronics Forum | Mon Jan 27 10:06:03 EST 2003 | binns

Just to set the record straight... Samsung did not build all Quad machines. QSA = Quad Samsung America, The QSA-30 machine platforms were manufactured by Samsung, utilizing Quad feeders, other Quad technology and Quad sales and service. Before the

Re: Quad vrs. Mydata

Electronics Forum | Thu Nov 12 00:02:45 EST 1998 | Gang Pan

I have just finished this excise which compared Mydata and Quad machine. As the result I purchased Quad QSV-1 model SMT assembler. In my opinion select which one that will depend on your applications. Also depend on what machines you compare with.

How to place cylindrical (MELF) parts on Quad P&P

Electronics Forum | Fri Nov 05 11:30:53 EDT 2010 | deanm

We have a Quad QSV-1 pick and place machine that has performed fine for us with the exception of cylindrical glass (MELF) type diodes. The machine often fails to pick these out of the tape to the point where it is easier to hand place them. As far

Quad QSV-1 randomly destroying Z-rods

Electronics Forum | Sun May 11 17:29:17 EDT 2014 | bobpan

Most times when the machine oscillates when closing the doors it will be a problem with the digital i/o cards. I would check that the dip switch settings are correct. If they are correct i would look at replacing both of the cards. The boards are sub

Advice on used pick and place machine

Electronics Forum | Mon Oct 09 13:36:30 EDT 2006 | ppminc

Phil, The QSA-30 was built by Sam Sung, Sold by Quad. Single Head 2 Nozzles around 11K CPH Quad does not support the machine but I believe you can get parts direct from Sam Sung. I am not sure if they have a registration fee. The QSA used Quad made

PCB Warp Issues

Electronics Forum | Fri Jul 16 17:39:33 EDT 2010 | deanm

It is a PCB design issue where the copper patterns are not balanced among the layers. Baking the boards in order to correct the warpage will not improve it. We've had a problem with one bare board in particular warping the same way from two differen

Re: Backplane Assembly Info Request

Electronics Forum | Mon Mar 08 11:46:38 EST 1999 | Wendy Casker

Hello; I am looking for general info on backplane assemblies. Any info would be appreciated, but some of the questions that come to mind include: -What part types other than connectors do backplane cards have on them? SMT? Leaded? Qua

Previous 3 4 5 6 7 8 9  

qsv-1 searches for Companies, Equipment, Machines, Suppliers & Information