Electronics Forum: soltec (Page 8 of 30)

Soltec 6622cc fault

Electronics Forum | Thu Dec 03 03:13:11 EST 2015 | polar121

Hi has anyone had a fault with a soltec deltawave model 6622cc were the following functions all turn off for no reason Preheat zone1 and 2 the fluxer and the solder wave pump this has been happening for the last couple of weeks and seems to be getti

Solder Wave Vitronics Soltec Delta 3 TRACKING problem

Electronics Forum | Mon Apr 09 09:39:40 EDT 2018 | justconmac

Having an issue with tracking for the Vitronics Soltec Delta 3. Wave will not give error on "expected PCB at exit" but will still show 1+ pcb's in the wave when the machine is empty. This is causing solder pump to idle unnecessarily. Outfeed sensor i

Vectra Question

Electronics Forum | Fri Aug 04 12:16:41 EDT 2006 | Wave Master Larry

LISTEN Dr Shocker. you're a doctor of what again? That's what you get for having those god awful Vecra machines.We've got a couple of those at my place of employment and I tell ya I hate that new fangled windows software that it runs on. I would say

Compare Soltec to Ursa Reflow Ovens

Electronics Forum | Sun Nov 19 23:28:38 EST 2000 | Richard Metrton

Hi, We are looking at both the Vitronics Soltec and the Ursa Hotflow with the flux management options and am intrested to hear what others on the forum think about these two products. We really want something low maintenance, and works well. I gues

Re: Electrovert Econopak 100 or Soltec 6621

Electronics Forum | Tue Jun 01 15:09:58 EDT 1999 | Tony

Dear All, We are a medium sized sub contract manufacturing house, engaged in high mix, medium volume production. We are using no clean as well as Aqueous cleaning process. we are planning to buy a new wave soldering machine out of the follow

Re: Electrovert Econopak 100 or Soltec 6621

Electronics Forum | Wed Jun 02 04:04:58 EDT 1999 | Vinesh Gandhi

Dear All, We are a medium sized sub contract manufacturing house, engaged in high mix, medium volume production. We are using no clean as well as Aqueous cleaning process. we are planning to buy a new wave soldering machine out of the

Re: Electrovert Econopak 100 or Soltec 6621

Electronics Forum | Wed Jun 02 19:31:01 EDT 1999 | Tony

Dear All, We are a medium sized sub contract manufacturing house, engaged in high mix, medium volume production. We are using no clean as well as Aqueous cleaning process. we are planning to buy a new wave soldering machine out o

PCB intake speed on a Soltec oven

Electronics Forum | Tue Dec 13 12:56:17 EST 2005 | grantp

Hi, We have a problem sometimes where our soltec oven will accept another PCB too soon after it's taken the last one, so the PCB will collide with the last PCB that just enter the oven, and knock half the components off one of the boards, and destro

Problems with SN100C in a Soltec Delta C Wave

Electronics Forum | Mon Jun 12 09:07:10 EDT 2006 | JimC

Flux: Getting enough- is the spray fluxer getting good through-hole penetration. Try cranking it up. Soltec spray fluxers are not really as good as Ultrasonic Systems or Sonotek ultrasonics or the new ServoJET, but should do the job. Also, try anothe

Electrovert Econopak 100 or Soltec 6621

Electronics Forum | Tue Jun 01 07:17:00 EDT 1999 | Vinesh Gandhi

Dear All, We are a medium sized sub contract manufacturing house, engaged in high mix, medium volume production. We are using no clean as well as Aqueous cleaning process. we are planning to buy a new wave soldering machine out of the following op


soltec searches for Companies, Equipment, Machines, Suppliers & Information