Electronics Forum: cp6 servo amp error (Page 9 of 20)

DEK 265 Horizon Servo Following Error

Electronics Forum | Wed Dec 13 08:54:28 EST 2017 | raymccomb

We have a DEK 265 and we have fitted new belts to it after one split in use. when we set back up and run program A all is OK, when we go to run program B it has System Error. Servo Following Error - Fatal Error - Reinitialise machine. Does any one h

Pick Up Error

Electronics Forum | Thu Aug 05 20:33:48 EDT 2004 | Dhanish

The machine type is Fuji CP6.We have major issues with Network Resistor placement.The equipment guys often feedback there is a problem with nozzle and feeders.What will happened to the part if the Thickness data in the Part Data does not match the Pa

CP6-4000 FUJI TECH in CALIFORNIA???

Electronics Forum | Fri Jul 17 07:50:32 EDT 2009 | csm

Dear Jepoy We check the oilmatic system and I found a relay is not working, it will arrive until tomorrow. We still have 2 errors and 1 message, we are taking time because we don't have the Fuji CP6-4000 manuals or electric diagrams. we get this ma

Director Fuji Flexa + CP4

Electronics Forum | Tue Jul 17 15:26:08 EDT 2012 | kruzer

Hi I use CP4, CP6, CP643, GLV and NXT, but i have a problem with CPIV, i cant use It with Director Fuji Flexa. i use snifer rs232 (rs232mon) to resolve problem and what i know: Computer send on rs232 to machine (every 1 min or something): vQN2105

Error on FUJI IP-2

Electronics Forum | Fri May 06 16:19:40 EDT 2005 | jdengler

Does the problem happen at start-up? Does the servo amp have an error? If yes to both, could be a bad cable, or a badly tuned servo amp. If after running and the amp has an error it could still be the cable but also brings in things like a bad motor

CP6 Maintenance

Electronics Forum | Thu Jan 19 06:39:56 EST 2006 | dougs

It's been a few years since i worked on a CP machine but your st17 & 19 errors are probably down to grease in the clutches at the top of the shafts, if too much grease is put onto the turret gear during maintenance it tends to spray into these clutch

FUJI CP64 Service in San Diego CA area

Electronics Forum | Mon Jul 13 09:34:32 EDT 2009 | csm

Dear all, we have an Fuji CP6-4000 we get some weeks ago, but it shows an error "Hardward NG and show some actions (Inch the axis to cancel the overtravel. Then switch the power off and restart the machine). We did but display same error. I would

CP6-4000 FUJI TECH in CALIFORNIA???

Electronics Forum | Fri Jul 17 19:43:20 EDT 2009 | fujiphil

Have you eliminated the hardware N.G.? Check the connection for the rear door. If the connection are ok, try to bypass the key. short the two wires for the rear door. If the rear door problem is corrected, check the rear door switch physically. Reg

DEK 265 Horizon Servo Following Error

Electronics Forum | Fri Jan 05 03:32:46 EST 2018 | raymccomb

yes we resolved the engineer did not set the servo to zero so it did not know its datum start point.

Fuji CP troubleshooting

Electronics Forum | Mon Jan 10 17:00:56 EST 2005 | Johnw

you may have a servo reach pulse error go into mecha check and check zero dev


cp6 servo amp error searches for Companies, Equipment, Machines, Suppliers & Information

Flux-Free Reflow Soldering

Want to know where to find the best AOI system? - Read testimonials.
Digital Inspection Equipment

Best Reflow Oven
IPC Training & Certification - Blackfox

Easily dispense fine pitch components with ±25µm positioning accuracy.
Selective Conformal Coating System

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
Golden Tech Electronics

Thermal Transfer Materials.