Electronics Forum | Tue Feb 25 18:11:40 EST 2020 | kylehunter
> What we did not talk about is Mycronic machine. > Great choice for small batches. Yeah? That's what I keep hearing! Would use that exclusively for small runs, with the Opal for larger batches.
Electronics Forum | Mon Feb 24 07:18:07 EST 2020 | kylehunter
> If your ovens are 480V you may be able to convert > them back to 240V by changing out the elements? > There are industrial suppliers for oven elements > out there. sarason Yes that is true, our dealer can do that, but due to cost
Electronics Forum | Tue Feb 25 17:03:33 EST 2020 | kylehunter
LOL! Good to know! Yeah, we have 3Ph with a high leg, so technically at 240V, so we should be fine. Since nobody has really mentioned a real preference with the ovens, is it kinda like what I thought at first? That an 8 zone oven is an 8 zone oven.
Electronics Forum | Tue Feb 25 15:41:03 EST 2020 | SMTA-Alex
The ovens you're looking at need 100 amps of 480, 200 amps of 240. Do you have that extra power available in your building? You can go with a step-up transformer to convert 240V to 480V. My understanding is that ovens run more efficiently on 480V.
Electronics Forum | Tue Feb 25 16:45:45 EST 2020 | stephendo
One thing that you do not want to do is run a 240V oven at 220V. One place I worked a few lifetimes ago had an oven that had five top zones and only two on the ends on the bottom. It was something like 440V but supplied with 408V. It took a long long
Electronics Forum | Wed Jul 23 18:25:12 EDT 2008 | shanenaturalpoint
I just purchased a used Heller 1500 reflow oven for an SMT line that I am ting up. Looking for the CFM requirements for my exhaust venting. Does anyone out there have any information on what the minimum requirements are for pumping this exhaust out
Electronics Forum | Mon Feb 24 17:06:36 EST 2020 | emeto
It looks like one oven is 10years newer than the other, so if we assume same maintenance routine you should get another 10 years if life on it. On the TH side, you know your board complexity - for me wave have much more value than a Selective. Selec
Electronics Forum | Mon Jul 29 17:03:03 EDT 2002 | burb1999
Just setting up a new SMT line and have questions on which profiling product to use. So far the two in consideration are Super M.O.L.E. Gold and Slim KIC 2000... Please share any thoughts, experiences you have had with either and your opinion....
Electronics Forum | Mon Feb 24 16:30:07 EST 2020 | stephendo
You might be able to get a step up transformer although I would not recommend that unless it is a good solution for you. What is the input voltage to your facility? It is probably 600V (or something close). If so then you could get a step down transf
Electronics Forum | Wed Feb 26 09:16:42 EST 2020 | emeto
THese you can have single or dual head, long for a lot of feeder positions, with bigger or smaller work area based on your needs. Feeders concept is very clever and setups are quick. A lot can be done on the fly on the machine, compared to other bran
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, China
Phone: 0755-33578694
