Printed Circuit Board Assembly & PCB Design SMT Electronics Assembly Manufacturing Forum

Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.


solder paste printing

Views: 1457

#82041

solder paste printing | 20 February, 2019

what's the meaning of print pump head in solder paste printing

reply »

#82045

solder paste printing | 20 February, 2019

https://murraypercival.wordpress.com/2014/04/08/enclosed-pump-heads-for-stencil-printing/

reply »

#82245

solder paste printing | 29 March, 2019

I am still in confusion what does it mean? I simply have a heat pump which is the part of the HVAC in my home. It is not used over here I supposed.

reply »

#82249

solder paste printing | 29 March, 2019

“For a number of years now, work has been proceeding in order to bring perfection to the crudely conceived idea of a transmission that would not only supply inverse reactive current for use in unilateral phase detractors, but would also be capable of automatically synchronizing cardinal grammeters. Such an instrument is called "the pump print head."

Now basically the only new principle involved is that instead of power being generated by the relative motion of conductors and fluxes, it is produced by the modial interaction of magneto-reluctance and capacitive diractance.

The original pump print heads had a base plate of pre-famulated amulite surmounted by a malleable logarithmic casing in such a way that the two spurving bearings were in a direct line with the panametric fan. The latter consisted simply of six hydrocoptic marzlevanes, so fitted to the ambifacient lunar waneshaft that side fumbling was effectively prevented.

The main winding was of the normal lotus-o-delta type placed in panendermic semi-boloid slots of the stator, every seventh conductor being connected by a non-reversible tremie pipe to the differential girdle spring on the “up” end of the grammeters.

The pump print head has now reached a high level of development, and it’s being successfully used in the operation of novertrunnions. Moreover, whenever a forescent skor motion is required, it may also be employed in conjunction with a drawn reciprocation dingle arm, to reduce sinusoidal repleneration.”

Additionally, In the assembly of Printed Circuit Boards (PCBs) using Surface Mount Technology (SMT), solder paste is deposited on the bond pads of the PCBs using stencil/screen printing technique. The last few years have seen the development and introduction of new printing mechanism to meet the miniaturisation challenge of electronic products. The most notable is the development of new printing heads such as the ProFlow and the Rheometric Pumping Head. Unlike the traditional squeegee blade, in these new printing devices the solder paste is contained in a sealed pressurised chamber, and is released during the printing stroke via an opening as the printing head passes over the stencil apertures. The flow profile of the solder paste inside such a chamber plays a key role in determining the volume of solder paste deposited onto the PCB pads. In this paper we investigate the paste flow inside such a chamber and its influence on the aperture filling. Our results show that the paste does not vertically fill the apertures, but has a horizontal velocity component in the printing direction. This horizontal velocity component will lead to insufficient filling of paste at the rear corner of the aperture. To counteract the influence of this undesirable velocity component, we propose to introduce a horizontal shaft perpendicular to the printing direction inside the chamber. During a printing stroke this shaft rotates inside the chamber in the printing direction and drives the paste near the bottom slot to flow against the printing direction. We present an analysis of the paste flow inside such a device and the nature of the aperture filling process. The main parameters that influence the paste flow are the diameter, the rotational speed and the position of the shaft. The key to obtaining sufficient and consistent paste deposits is to minimise the horizontal velocity component of the paste to ensure the paste fills into the aperture vertically, and to maximise the vertical velocity component of the paste to shorten the aperture filling time. The introduction of such a shaft is also expected to significantly reduce the pressure loading on the paste at the top of the chamber.

reply »

#82251

solder paste printing | 29 March, 2019

WHAT?

reply »

#82255

solder paste printing | 29 March, 2019

I would say that is about the best answer to any question ever put on SMTNET

sarason

reply »

#82256

solder paste printing | 30 March, 2019

Thanks for the reply and this is the best one to get know about this print pump.

Detailed and brief information.

reply »

#82263

solder paste printing | 30 March, 2019

Very very few people in the world would have any reason or requirement to know anything about this print head pump. It is a specialized tool for manufacturing of electronics. It would be of no interest to anyone not directly involved with the manufacture of electronics. Do you manufacture electronics, specifically SMT components? IF not then you do not want to waste your time learning about print pump heads.

reply »

used pcb assembly equipment - lel semi

ADJUST-A-VAC Vacuum Tweezer for fragile components, wafers, MEMS devices tweezers