Printed Circuit Board Assembly & PCB Design SMT Electronics Assembly Manufacturing Forum

Printed Circuit Board Assembly & PCB Design Forum

SMT electronics assembly manufacturing forum.

lead free platings and tin lead



lead free platings and tin lead | 31 August, 2004


Any body have any issues soldering tin lead solder paste with lead free terminations ?

Components are leaded devices and chip components

have read the theoritical discussions on the forum, need to know if any body has seen any real issues todate

appreciate everyones help


reply »



lead free platings and tin lead | 31 August, 2004

Kris, this practice has gone on for years. I have never heard of any problems associated with this. I have heard "grumblings" about tin lead parts being processed with lead free paste, but have seen or heard of no data to support.


reply »


lead free platings and tin lead | 31 August, 2004

NO-LEAD COMPONENTS WITH LEAD SOLDER ISSUE: We agree with Russ. We've dicussed this several times on SMTnet. For instance, look here

LEAD COMPONENTS WITH NO-LEAD SOLDER ISSUE: We disagree with Russ. As with many things, there appears to be two distinct industry camps on the topic of lead contamination of no-lead solder joints. * One camp is of the opinion that the presence of lead is detrimental to no-lead solder joints and significantly reduces the thermal cycle fatigue life. * The opposing camp is of the opinion that the presence of lead does not impact or only slightly degrades a no-lead solder joint thermal cycle fatigue life.

Many solder suppliers recommend against using lead components with no-lead solder, because of weaker solder connections [discussed in the next paragraph].

Unfortunately, in the past the presence of lead in lead-free alloys has been presumed to be acceptable. The logic behind this was that tin and lead are soluble in a lead-free system. However, what has been overlooked is that the intermetallic crystalline structures in lead-free systems are not soluble and will precipitate at lead boundaries. Thus, when using a lead-free alloy to solder to Sn/Pb coated component leads, Pb can actually create voids in the solder joint that can result in joint failure. [from an AIM Solder presentation]

Dynamics of Lead Contaminated Solder Joint Failure [from an AIM Solder presentation] * It is important to note that lead that contaminates a lead-free solder joint is not distributed uniformly through the joint; rather, the Pb localizes in the last point to cool. * This is similar in dynamics to �zone refining�, a process utilized to refine high-purity elements. In zone refining, a heat source traverses across a billet. As this occurs, the elemental impurities are collected in the liquid phase and are condensed at the last point to cool (the end of the billet), which is then removed. * Just as in zone refining, lead as an impurity in a solder joint migrates to the last area of the joint to cool. This occurs under the middle of the component lead at the solder joint-PCB interface. * When this occurs, the joint forms pockets and the grain structure is disturbed. These Pb-rich regions are lower in melting temperature and may cause dewetting during soldering. * This is inevitably the area of a solder joint that results in a failure.

Let's not kid ourselves, we're going to be building [and dealing with field failures and having freaked-up general managers] with lead contaminated no-lead solder connections for years. [And that's why the solder suppliers are recommending not using leaded parts with no-lead solder. So that when the failures start piling-up, they can say, "See we told them not to mix materials, like that, but did they listen? Nooo!!! Our hands are clean."]

reply »



lead free platings and tin lead | 31 August, 2004

Now see Dave, now I have some good info on why it is "bad", This must be the lead enrichment I have heard about but never got any substantiated data or explanantion. I wonder how much weaker or less reliable these are. Is there any data that you know of that shows actual numbers or case histories. I actually have a customer that requires us to use lead free paste but they can never seem to get all pb free parts for the builds. I actually have told them that I have heard that it was not a goood idea to do this for the reasons you stated but could not go any further in explanantion due to ignorance on my part.

Thanks Russ

reply »


lead free platings and tin lead | 31 August, 2004

See Russ, that's why we're all here. => To take our turn at keeping everyone else on the straight and narrow.

For more on lead contamination of no-lead solder, look here:

[We apologize to all for appearing to be such a pimp for AIM Solder in this thread, but we gain no benefit from AIM. AIM has been very aggressive in educating practitioners in the issues of no-lead. We're sure other solder suppliers have made equal efforts, but it's just that we're unaware of their work.]

reply »



lead free platings and tin lead | 31 August, 2004

I have experienced this directly in SMT and wave solder.

Fillet lift (can) be a direct indicator to lead enrichment (but its not the exclusive symptom).

Lead enrichment in smt joints reduces the interfacial strength shortening the time to creep fatigue failure

I read a study that indicated thet TH joints were only margionally less reliable than those without lead enrichment. However, within SMT joints there was a more pronounced affect (naturally, this is different with different types of smt components).

I think what is important here is fact its something most folks seem to miss

Lead bearing solders can be used with lead free components and produce a given reliability that will (generally) not be less than (the baseline) SnPb solders and SnPb parts.

You can use tin/lead parts with lead free solders (lets assume SnAuCu) and produce a given reliability that (possibly) will equal or be less than the baseline tin/lead assembly.

However, there are so many factors that influenc joint reliability (component design, Th/SMT, choice of LF solder etc.). The best method to determin what is best for you and your product is thermo-mechanical fatigue testing using HALT.

There is no perfect answer. Lead bearing solders have over 40 years of tried and true experience in Electronics.

reply »

Precision Auger Dispense Pump

Online IPC Training & Certification