Printed Circuit Board Assembly & PCB Design Forum
SMT electronics assembly manufacturing forum.
Views: 11760
Hello everyone! I'm new to this forum. I just got back into ...
- Jan 18, 2006
by
Daxman
It's been a few years since i worked on a CP machine but you...
- Jan 19, 2006
by
St17 and 19.
One thing you could do is to swap heads and ...
- Jan 19, 2006
by
We've checked the Amplifiers, and the optics and they seem t...
- Jan 19, 2006
by
Daxman
i think it's more likely to be greasy/dirty shaft clutches, ...
- Jan 20, 2006
by
i have a problem similar to Daxman where cp6 usually having ...
- Jan 21, 2006
by
sorry, st17 not st19
...
- Jan 21, 2006
by
don't use any lubrication in the clutches, they should be cl...
- Jan 23, 2006
by
We use an alignment jig {from Fuji I believe} that checks an...
- Jan 31, 2006
by
Chad
You may also make sure to use the adequate lubricants. _Have...
- Jan 31, 2006
by
Hello, Please call 319-392-4674 8 to 5 CST. for all Fuji...
- Jan 31, 2006
by
Are you seeing this problem with the nozzles after an error ...
- Feb 01, 2006
by
You guys hurting for money again Bill or Rex? Stop advertisi...
- Feb 02, 2006
by
Daxman,
The noise you are hearing is a worn out coupling ...
- Feb 03, 2006
by
Sr. Tech
Sr Tech could be right about the C-AXIS coupling, i've seen ...
- Feb 06, 2006
by
Hi guys,
Sorry I haven't posted in awhile...but here are ...
- Mar 28, 2006
by
Dax,
You need to clean out those clutches. Even if they see...
- Mar 29, 2006
by
Sr. Tech
Find you a good degreaser to clean the clutches with. Fuji u...
- Mar 29, 2006
by
I do not reccomend spraying anything into those clutches. Th...
- Mar 30, 2006
by
Sr. Tech
Obviously you are not as experienced as you think so I will ...
- Mar 30, 2006
by
Also why I am at it. In the book CP-6 Series Maintenance Man...
- Mar 30, 2006
by
Fuji has said a lot of things in the past, then changed it l...
- Mar 30, 2006
by
Sr. Tech
So you use the dogbone alignment jig and the 3mm allen wrenc...
- Mar 30, 2006
by
I bet my bicepes are bigger than yours.
Just kiding.
I do ...
- Mar 30, 2006
by
Daxman
It could be related but it is kinda hard to tell from just t...
- Mar 31, 2006
by
I'm not sure if we are on the same page here....maybe i'm lo...
- Mar 31, 2006
by
Daxman
DAX ! You don't need to remove the entire shaft assembly to...
- Apr 01, 2006
by
Sr. Tech
Hey Sr.Tech, thanks for the heads-up.
I'm familar with the ...
- Apr 03, 2006
by
Daxman
shouldn't be if you put them all back in in the order they c...
- Apr 03, 2006
by
I agree.
If you put them back in the same place you should...
- Apr 03, 2006
by
Sr. Tech
Okay, we got the machine back together about 2 weeks ago, cl...
- Apr 17, 2006
by
Daxman
I think your refering to the sleeve. It is held in with loct...
- Apr 21, 2006
by
newton