AKS Ultrasonic Stencil Cleaner
Company Information:
Name: |
AKS Ultrasonic Stencil Cleaner |
Category: |
|
Offered by: |
|
AKS Ultrasonic Stencil Cleaner Description:
Maximize your stencil cleaning results!
AKS Stencil Cleaner provides microscopic, ultrasonic removal of solder paste and post-solder flux buildup. All-in-one cleaning All “workstations” included in one compact unit, minimizing required floorspace. Easy load and unload. profile, top-centric design requires no or minimal bending. Entire system moves easily on sturdy wheels. Closed-loop filtration system. Dimensions: 40.75" by 33.5" by 36.5" high. Stainless steel tank and lift-off covers.
Easy to program and operate, simply place your stencil in the rack and press the start button. The stencil cleaner will lower your stencil into the wash tank, which is filled with high quality detergent, and is ultrasonically cleaned by high-speed microscopic bubble implosions. After only a few minutes, it then lifts your cleaned stencil from the wash, and you spray-clean by hand to remove the loosened solder paste and other contaminants. Last, you use a low-pressure dry air gun removes the remnant rinse moisture and your stencil is ready to be used again - all in only a few minutes time!
Benefits of the AKS Stencil Cleaner
- Complete cleaning - Microscopic, ultrasonic removal of solder paste, post solder flux build-up, and more
- All-in-one cleaning - All “workstations” included in one compact unit, minimizing required floorspace
- Easy loading and unloading - Low-profile, top-centric design requires no or minimal bending
- Portability - The entire systems moves easily around your shop on sturdy wheels
- Conservation of detergent - From wash station filter that extends chemical life
- Conservation of waste water - From closed-loop filtration system
- Easy maintenance - With easy-to-access, easy-to-replace parts
Specifications:
| First Sump Dimensions: | 31" left to right by 6" front to back by 26.75" deep (24.75" liquid depth) |
| First Sump Capacity: | 20 gallons |
| Second Sump Dimensions: | 31" left to right by 10" front to back by 30.5" deep (27.5" liquid depth) |
| Second Sump Capacity: | 37 gallons |
| Overall Dimensions: | 40.75" left to right by 33.5" front to back by 36.5" high |
| Process: | Wash, Rinse |
| Chemistry: | Water |
| Facilities: | 1-3 GPM (4-6 GPM on demand) DIW@ 1-2 Mohm, 30-35 psi and process temperature, 65-70 CFM CDA @ 30 psi, 1-2 CFM shop air @ 60 psi, unrestricted floor drain |
| Power Requirements: | 240 volts/60 Hz/1 phase, 25 amps |
| Ultrasonic Frequency: | 40 kHz |
| Ultrasonic Density: | 50 watts per gallon |
| Ultrasonic Timer: | An analog panel-mounted timer with buzzer |
| Heat: | 4000 watts of strip heat at first sump |
| Temperature control: | A 0-250°F panel mounted thermostat |
| Blow Off: | A PVDF air blow off gun with 6ft stainless steel braided hose. Include a filter regulator with gauge |
| Spray Rinse: | A PVDF spray gun with 6ft stainless steel braided hose |
| Standard Features: | Stainless steel lift off covers, A float-type low liquid level safety, A capillary bulb-type over temperature safety thermostat |
| Basket: | Mesh basket size 29” X 5” X 26.25” with built-in drip handles |
| Tank Material: | Type 316L stainless steel with a #2B finish |
| Cart Material: | Powder coated black roll around cart with fitted casters |
| Plumbing: | Complete hard plumbed process piping with all appropriate flow control and isolation ball valves |
| Electrical: | A NEMA 12 enclosure with all the control mounts to the right side of the console |
AKS Ultrasonic Stencil Cleaner was added in Feb 2015
AKS Ultrasonic Stencil Cleaner has been viewed 689 times
