Electronics Forum: galaxy power on (Page 1 of 9)

Thermals on BGA vias to power plane

Electronics Forum | Mon Mar 23 15:41:46 EST 1998 | Stuart Adams

Should I use thermals or direct connects on vias from BGA pads to power planes. The via is connected to the BGA pad via a short 8mil trace.

Quad 4C completely hangs on power up

Electronics Forum | Fri Jan 03 15:16:54 EST 2014 | ppminc

If all of the lights are on, on the operator interface panel usually that means the EPCU is defective or not fully seated correctly. If you swapped out the EPCU board from another machine you need to make sure its the same type of machine. If it has

Quad 4C completely hangs on power up

Electronics Forum | Mon Dec 30 21:38:56 EST 2013 | jkoughan

I've got a scary one for you guys and desperately need your help - We just purchased a second Quad 4C and had some communication problems when we first turned it on (we're still working on that issue). To chase down the problem, we decided to start

Quad 4C completely hangs on power up

Electronics Forum | Thu Jan 02 04:56:38 EST 2014 | bobpan

Here is a couple of things to look at: 1. Make sure the boards are plugged into the correct position. Also just leave out the transport card to see if its hanging up the machine. The transport board should be the board all the way to the right. 2. M

Re: Thermals on BGA vias to power plane

Electronics Forum | Tue Mar 24 13:21:16 EST 1998 | Earl Moon

| Should I use thermals or direct connects on | vias from BGA pads to power planes. The via is | connected to the BGA pad via a short 8mil trace. Thermals are safest. However, I have had no problems using direct connects provided parameters are capab

AIS3500 on GSM1

Electronics Forum | Wed May 19 17:54:41 EDT 2010 | gregcr

I have had problems corrected by swapping or replacing the power supplies in the box. Do you have a second GSM that runs the AIS3500 box? If so swap the power supply and see if the problem follows the swap. I have replaced the supplies inside the

advice on used P&P

Electronics Forum | Tue Jun 23 14:08:59 EDT 2020 | stephendo

The power outside your building will certainly be 3 phase. The power to your building will almost certainly be 3 phase. Why not simply get a transformer and have 3 phase power available for the machine? It will probably be a much better option than l

AIS3500 on GSM1

Electronics Forum | Fri May 14 09:34:18 EDT 2010 | lockj69w

This procedure is from UIC's knowledge base. TO run Diagnostics on AISI 3500 vision. Use of this procedure will require reloading of vision executive once complete. 1. verify PC1 COMM2 is connected to COMM2 on the RADISYS board in slot 1 of VME chass

Logicomm on GSM

Electronics Forum | Wed Jan 06 19:44:17 EST 2021 | ttheis

I am trying to look at logicomm messages on my gsm machine but I don't seem to be doing something correctly. I don't see any messages or have any prompt in the logicomm.exe window, just a black screen with a flashing cursor. I powered down, connecte

advice on used P&P

Electronics Forum | Tue Jun 23 02:51:19 EDT 2020 | jmelson

Emerald needs 3 phase power. What would be your price for the Emerald with 50 feeders? Where are these machines? We are in the St. louis, MO area. Thanks, Jon

  1 2 3 4 5 6 7 8 9 Next

galaxy power on searches for Companies, Equipment, Machines, Suppliers & Information

Count On Tools, Inc.
Count On Tools, Inc.

COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.

Manufacturer

2481 Hilton Drive
Gainesville, GA USA

Phone: (770) 538-0411

Software for SMT

World's Best Reflow Oven Customizable for Unique Applications
pressure curing ovens

We offer SMT Nozzles, feeders and spare parts globally. Find out more
SMT feeders

High Precision Fluid Dispensers
SMT feeders

High Throughput Reflow Oven
Circuit Board, PCB Assembly & electronics manufacturing service provider

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.