Electronics Forum: layout programming (Page 1 of 5)

Fuji cp43 pcb layout

Electronics Forum | Thu Oct 30 21:06:20 EDT 2008 | ashley

Hello mickd, For Fuji practice, the primary tooling hole preferably be 5mm from the edge of the PCB (lower right hand corner). This is the reference X0, Y0 co-ordinates in the Fuji program where placing co-ordinates going LEFT will be -ve value & go

Fuji cp43 pcb layout

Electronics Forum | Sat Nov 01 04:12:53 EDT 2008 | ashley

Hello mickd, The Fiducial Marks are normally etched along the vertical side of the PCB, therefore it will not be block by the XY table clamping rails. p.s. try to have a Shiny & Round Fiducial Mark as recommended by Fuji....so that you need not inp

MyDATA programming

Electronics Forum | Mon Mar 13 13:23:20 EST 2006 | stepheniii

Get a book on effective complaining. Gerbers is not a good way to program. Matching up the designators is but one headache. At the very least try and get centroid data. But try for ascii cad files. Are there any programs that generate gerbers but ca

Re: COB module design / layout

Electronics Forum | Thu Oct 26 17:48:47 EDT 2000 | Dave F

In response to your questions: 1) Suggestions on substrate material FR-4 or something better? Most PBGA are on BT. That might good for you, also. 2) Are there design guidelines for wire bonding pattern on the substrate? Several things: 1 Doesn�t

NEW to Philips Topaz-X need help programming

Electronics Forum | Fri Sep 26 09:47:34 EDT 2008 | kevslatvin

I hope this doesn't add any confusion. I save my data as a .csv file and bring that into Cad2cad. This is how I was shown to do it by Assembleon. To use .csv you have to set your file format on the format cad file tab(during import to Cad2cad) to Cha

SMT DUAL PROCESS

Electronics Forum | Sun Nov 01 10:34:43 EST 2009 | greg_diaz

If you have an even multiple of boards in a panel, then your layout can be altered to have 1 top 1 bottom in the x layout so that when you flip the panel the same layout is on the opposite side therefore requiring just one program.

Tp9 and Tp9 ufp

Electronics Forum | Wed Oct 26 11:02:41 EDT 2011 | dyoungquist

TP9 machines are good, but old machines. We ran a TP9 for many years. As the machine got older it required more and more maintenance and had more frequent small issues similar to what you are seeing. We only saw 1 of your 4 issues specifically whi

PHILIPS CSM 84 BOARD PROGRAMING

Electronics Forum | Sat Jun 05 08:45:30 EDT 2004 | vinitverma

Hi Adrian, You need the UFOS program. If you send me the cad data, and the BOM, and the board layout, I can make a sample program for you to check. However the program shall not be optimized and the head nos., feeder nos., and the vision files will

Re: Mylar to Gerber

Electronics Forum | Mon Oct 05 13:58:20 EDT 1998 | Dave F

| Anyone know of someone who can convert mylar top layer board data to Gerber data? We have some old designs that all other data is now lost. | Jerry: You could tape the mylars to a digitizer pad and enter the layout into your PCB layout program o

Please HELP! Need to purchase a few machines

Electronics Forum | Fri Feb 01 02:32:31 EST 2019 | robl

It's nice to be able to do things in house, and it's good to have somewhere without commercial pressures to learn and make mistakes, so I can understand where you are trying to go. Those machines look a little lightweight for consistent quality pr

  1 2 3 4 5 Next

layout programming searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

Software for SMT placement & AOI - Free Download.
Sell Used SMT & Test Equipment

High Precision Fluid Dispensers
Circuit Board, PCB Assembly & electronics manufacturing service provider

World's Best Reflow Oven Customizable for Unique Applications