Technical Library | 2022-07-11 09:24:48.0
The change of squeegee pressure has a significant impact on printing. Too small pressure will make the solder paste unable to effectively reach the bottom of the stencil opening and not be well deposited on the pad. Too much pressure will cause tin The paste is printed too thin and can even damage the stencil.
Technical Library | 2007-12-27 11:41:37.0
The latest screen printing platforms unlock more of the potential from dual-lane processing. Simultaneous demands to enhance flexibility while increasing utilisation and overall throughput apply to manufacturers operating at virtually any point in the mix-volume continuum: capacity must work hard to deliver the required return. As these lean manufacturing principles hold sway from the US and Europe to the Far East, no modern assembler has a second to spare.
Technical Library | 2012-05-03 20:40:10.0
First published in the 2012 IPC APEX EXPO technical conference proceedings. Increased pressures to reduce time to market and time to volume have forced many manufacturers of populated printed circuit boards to rely on capacitively coupled, un-powered, vec
Technical Library | 2007-12-13 17:03:02.0
Printer-hosted processes for solder ball placement are now widely used for package technologies ranging from BGAs using ball diameters above 750μm to the latest WL-CSPs demanding 250μm diameter. This broadening spectrum of applications brings more choices in terms of stencil design rules and production methodologies.
Technical Library | 2018-03-07 22:41:05.0
This study investigates the scooping effect during solder paste printing as a function of aperture width, aperture length and squeegee pressure. The percent of the theoretical volume deposited depends on the PWB topography. A typical bimodal percent volume distribution is attributed to poor release apertures and large apertures, where scooping takes place, yielding percent volumes 100%. This printing experiment is done with a concomitant validation of the printing process using standard 3D Solder Paste Inspection (SPI) equipment.
Technical Library | 2010-04-15 20:42:44.0
The high level of current interest in embedded passives in printed circuit boards is driven by the tremendous pressure to pack more circuitry into smaller spaces. However, adoption has been limited due to design, prototyping and infrastructure issues, as well as the stability and tolerances necessary for widespread replacement of discretes. The focus of this work has been to develop a polymer thick film resistor technology to incorporate reliable organic resistors inside printed wiring boards using standard PWB processing.
Technical Library | 2007-09-27 16:18:15.0
Considerable interest exists in the process known as the pinin- paste, or the Alternative Assembly and Reflow Technology (AART) process. The AART process allows for the simultaneous reflow of both odd-form and through hole devices as well as surface mount components. This process has several advantages over the typical mixed technology process sequence that includes wave soldering and/or hand soldering, often in addition to reflow soldering.
Technical Library | 2008-12-18 01:34:49.0
Unless you've been living under a rock the past several years, you are no doubt keenly aware of the global drive toward alternative energy sources. Certainly this initiative is attractive because of the clear environmental benefits of developing fossil fuel substitutes, but also because of potential economic benefit. Although fuel cell technology has been proven viable for various applications, the production costs still remain relatively high, and further process development to promote low-cost, high-volume manufacturing is required to reach a price point that encourages widespread consumer acceptance.
Technical Library | 2023-06-12 18:33:29.0
This paper presents a real-time predictive approach to improve solder paste stencil printing cycle decision making process in surface mount assembly lines. Stencil cleaning is a critical process that influences the quality and efficiency of printing circuit board. Stencil cleaning operation depends on various process variables, such as printing speed, printing pressure, and aperture shape. The objective of this research is to help efficiently decide stencil printing cleaning cycle by applying data-driven predictive methods. To predict the printed circuit board quality level, a recurrent neural network (RNN) is applied to obtain the printing performance for the different cleaning aging. In the prediction model, not only the previous printing performance statuses are included, but also the printing settings are used to enhance the RNN learning. The model is tested using data collected from an actual solder paste stencil printing line. Based on the predicted printing performance level, the model can help automatically identify the possible cleaning cycle in practice. The results indicate that the proposed model architecture can predictively provide accurate solder paste printing process information to decision makers and increase the quality of the stencil printing process.
Technical Library | 2019-05-01 23:18:27.0
Moisture can accelerate various failure mechanisms in printed circuit board assemblies. Moisture can be initially present in the epoxy glass prepreg, absorbed during the wet processes in printed circuit board manufacturing, or diffuse into the printed circuit board during storage. Moisture can reside in the resin, resin/glass interfaces, and micro-cracks or voids due to defects. Higher reflow temperatures associated with lead-free processing increase the vapor pressure, which can lead to higher amounts of moisture uptake compared to eutectic tin-lead reflow processes. In addition to cohesive or adhesive failures within the printed circuit board that lead to cracking and delamination, moisture can also lead to the creation of low impedance paths due to metal migration, interfacial degradation resulting in conductive filament formation, and changes in dimensional stability. Studies have shown that moisture can also reduce the glass-transition temperature and increase the dielectric constant, leading to a reduction in circuit switching speeds and an increase in propagation delay times. This paper provides an overview of printed circuit board fabrication, followed by a brief discussion of moisture diffusion processes, governing models, and dependent variables. We then present guidelines for printed circuit board handling and storage during various stages of production and fabrication so as to mitigate moisture-induced failures.
