Electronics Forum: (4) (Page 6 of 630)

4 mil epoxy dot dispensing

Electronics Forum | Wed May 20 05:50:08 EDT 2020 | tima

Hello colleagues, Question. Who ever done 4 mil (100uM) electro conductive epoxy dispensing? is it even possible? I did 6 mil but very unstable results... Now I need 4 mil for an application.

fuji cp-4 vision system

Electronics Forum | Tue Jul 14 21:31:19 EDT 1998 | Wen-han Tan

We just have a use cp4 .I have a problem on transfering data between cp3 to cp4 .when I use the data for cp4 I can't have parts in correct location. Is that normal? or it's because that has a different vision system.if so.how can i do with it.the dat

Questions on J-STD-033A procedure (Table 4-1)

Electronics Forum | Fri Feb 17 16:46:29 EST 2006 | GS

Hi CW, mine is not the answer to your questions, but I suggest you to take a look of the latest level of J-STD-033B (October 2005) The J-STD-033A was from July-2002, and several important points are different from latest level. For instance, in Cha

Questions on J-STD-033A procedure (Table 4-1)

Electronics Forum | Fri Feb 17 16:50:58 EST 2006 | GS

Hi CW, mine is not the answer to your questions, but I suggest you to take a look of the latest level of J-STD-033B (October 2005) The J-STD-033A was from July-2002, and several important points are different from latest level.For instance, J-

Juki optimisation

Electronics Forum | Fri Mar 23 19:50:57 EDT 2007 | Frank

Possible head combinations to pick from multiple 12, 16, or 24mm feeders. Note: you can not mix feeder sizes for simultaneous picks. KE-2010 and KE-2050 will use 1&3, 2&4, or 1&4 KE-2020 and KE-2060 will use 1,3,R or 2,4,R or 1,4,R I prefer to s

Disassembling a Fuji CP4-2

Electronics Forum | Fri Nov 20 01:00:50 EST 2015 | anilwagh

I am looking below parts of CP4-2. 1)1P150E-24-2 3)2MMB500U-01-1 3)3MMB50-4-1 4)4P300E-05-1 5)CACR-SR03BC IKS-Y264-1 6)CACR-SR10BC 1KS-Y262-1 7)CACR-SR44 BC 1BF-Y279-1

Re: fuji cp-4 vision system

Electronics Forum | Wed Jul 15 06:32:03 EDT 1998 | Process Engineer

We just have a use cp4 .I have a problem on transfering data between cp3 to cp4 .when I use the data for cp4 I can't have parts in correct location. Is that normal? or it's because that has a different vision system.if so.how can i do with it.the d

Gel Flex Tooling

Electronics Forum | Thu Jun 03 18:11:07 EDT 2004 | Rob

The price was actually $6,372 and it included the following: AP/UP2000 1011859 KIT,GEL-FLEX,AP/UP2000,SYSTEM The kit includes: quantity 12 1011557 BAR,GEL,ASSY quantity 4 1010934 SUPPORT,EDGE,3.31 quantity 4 1010935 SUPPORT,EDGE,4.

parts left on a reel

Electronics Forum | Wed Aug 22 07:24:34 EDT 2012 | ericrr

how about this for resistor & capactors with 4mm pitch, all measurements in millimeters. cell A1 "Input inside diameter" answer in cell B1 cell A2 "Input outside diameter"answer in cell B2 cell A3 "Input layer width,(from inner to outside layer) (no

SMT Components

Electronics Forum | Thu Jul 18 12:44:24 EDT 2013 | ericrr

after checking two computers, did not find it. However after using "google" found it in a flash. (less than 0.22 seconds) using a spreadsheet. how about this for resistor & capacitors with 4mm pitch, all measurements in millimeters. cell A1 "input


(4) searches for Companies, Equipment, Machines, Suppliers & Information