Electronics Forum: nozzle and repair ersa (Page 1 of 2)

Rework and repair system suggestions

Electronics Forum | Thu Jan 27 11:33:59 EST 2005 | russ

For what you have right now I would recommend that you use soldering iron tips that are made for component removal. until you get BGAs I wouldn't worry a whole lot about the expensive rework equipment. I would use specialty tips and a heat gun wit

Rework and repair system suggestions

Electronics Forum | Thu Jan 27 06:39:59 EST 2005 | reash

For now, on this first board, we will be reworking components such as 0805 and 1210 size caps and resistors, along with SOT-23 and SC-70 size packages. We might eventually get into BGAs. This board will most likely be a double-sided board, probably

Universal GSM and 0402/0201 Placement

Electronics Forum | Fri Jan 16 15:46:07 EST 2015 | comatose

We did 0402s for years on a GSM. Is this a flexjet or a 4 spindle head? A flexjet is easy with 0402s. The four spindle nozzles are big, you run into issues with knocking already places parts and having to Z zone carefully (and beware repair cycles.)

Re: Fountain Wave Soldering and Repair/Rework Equipment

Electronics Forum | Fri Jan 22 15:48:14 EST 1999 | Chrys

| Hello, | | I will be evaluating and qualifying two equipment types. The first is a fountain soldering device. I need practical advice on all the stuff you guys and gals know about as good, bad, ugly, best applications, setup, limitations, and all

QFP on going on square (now and again)

Electronics Forum | Tue Apr 02 13:43:54 EDT 2013 | ericrr

On one of the products uses a QFP (Quad Flat Package)which is not going on straight, maybe 20 pins per 4 sides. sometimes I have to tweak the alignment before the board goes in the oven, this practice can be a bit of a worry if you over tweak it - pa

BGA rework systems

Electronics Forum | Mon Nov 25 13:00:12 EST 2002 | steve

Ersa is the choice for lower end repair and rework systems. Airvac is the choice for higher end systems. Stay away from low end hot air units. They typically do not present an even flow of heat across the component. The Ersa requires no nozzles, whic

Re: IR rework stations

Electronics Forum | Tue Sep 28 04:07:33 EDT 1999 | Jacqueline Coia

| | | | | | | Hiya, | | | | | | | | | | | | | | Could anyone please suggest recommended manufacturers of | | | | | | | IR rework stations for the removal of various SMT comps. | | | | | | | | | | | | | | Cheers | | | | | | | | | | | | | Why IR ?

Re: IR rework stations

Electronics Forum | Tue Sep 28 04:27:04 EDT 1999 | Wolfgang Busko

| | | | | | | | Hiya, | | | | | | | | | | | | | | | | Could anyone please suggest recommended manufacturers of | | | | | | | | IR rework stations for the removal of various SMT comps. | | | | | | | | | | | | | | | | Cheers | | | | | | | | | | | |

Re: IR rework stations

Electronics Forum | Tue Sep 28 08:55:21 EDT 1999 | Earl Moon

| | | | | | | | | | | Hiya, | | | | | | | | | | | | | | | | | | | | | | Could anyone please suggest recommended manufacturers of | | | | | | | | | | | IR rework stations for the removal of various SMT comps. | | | | | | | | | | | | | | | | | | | |

Re: IR rework stations

Electronics Forum | Tue Sep 28 05:58:59 EDT 1999 | Wolfgang Busko

| | | | | | | | | | Hiya, | | | | | | | | | | | | | | | | | | | | Could anyone please suggest recommended manufacturers of | | | | | | | | | | IR rework stations for the removal of various SMT comps. | | | | | | | | | | | | | | | | | | | | Cheers

  1 2 Next

nozzle and repair ersa searches for Companies, Equipment, Machines, Suppliers & Information