Electronics Forum | Thu Sep 17 15:21:50 EDT 2020 | lpbro
For height, I start +-2mil usually. For 3mil stencils, my lower limit starts at 1.5mil, upper is 5. If the area is chem ethed, I normally add .5 to the stencil height. My default volume is 60 - 160%. Then print specs are adjusted till I see fit, then
Electronics Forum | Thu Jun 03 06:14:38 EDT 2021 | bukas
Yes, most of my fiducials are 1 mm. BUT, you may consider going 1.5mm or even better 2 mm because in my experience PCB manufacturers will NOT check fiducial shape during PCB testing. This goes for fiducials that are placed on panel frame. Fiducilas t
Electronics Forum | Wed Jan 20 14:21:54 EST 1999 | Dave F
| I need some opinions (And I know everybody has one). | I am mounting a board into a case, after mounting the board | I am loading it with stress in the middle causing it to bend around .030 inch. The board is 4" X 6" and is Bending in the 4" dire
Electronics Forum | Thu Feb 17 22:30:09 EST 2000 | Dave F
Alberto: There's no rules, but it works sorta like this: RESISTORS Usually marked in ohms using a standard code: First two numbers is the value Third number is the multiplier 102 = 1.0 x 10� ohm = 1000 ohm = 1 kW CAPACITOR Usually not marked. When
Electronics Forum | Thu Feb 17 22:30:09 EST 2000 | Dave F
Alberto: There's no rules, but it works sorta like this: RESISTORS Usually marked in ohms using a standard code: First two numbers is the value Third number is the multiplier 102 = 1.0 x 10� ohm = 1000 ohm = 1 kW CAPACITOR Usually not marked. When
Electronics Forum | Tue Oct 10 12:56:15 EDT 2000 | Ken Van ZIll
I agree that homplate is a good design, but also this could be caused by the stencil thickness and aperture size, if you are at 7-9 mils thick stencil and a 1:1 ratio on aperture size then 2 things i know of will happen, one a squishing out of past o
Electronics Forum | Fri Jun 11 03:39:26 EDT 1999 | Gyver
| | | | Hello all! | | | | Recently we got a problem about the Funtional test. Some boards passed tests by using the auto-fixture(vacuum), but failed by using manual test fixture(need to plug CPU, DIMM etc.). The error symptom is no picture. We doubt
Electronics Forum | Tue Feb 02 10:18:56 EST 1999 | Justin Medernach
| I have a recent design (1 component side only) that calls for 2 surface mounted antenna's (brass plated) to be mounted on a PCB. The problem arises when the PCB is 18x11.25 and has 15 to 20 PCB's in the pallet (IE weight, fixturing to hold the ant
Electronics Forum | Tue Feb 16 13:57:50 EST 1999 | Ron Beasley
| | I have a recent design (1 component side only) that calls for 2 surface mounted antenna's (brass plated) to be mounted on a PCB. The problem arises when the PCB is 18x11.25 and has 15 to 20 PCB's in the pallet (IE weight, fixturing to hold the a
Electronics Forum | Tue Sep 20 14:13:43 EDT 2005 | Rich
I use Cad2Cad v1.5 with Phillips Topaz. I don't know how much is differs, try this: Converting data to a Philips VIOS Text File format: 1. Open the pick and place data in Excel and format it to look like table 1. ** Make sure you delete the �mm�
.gif)
