Electronics Forum: 1..4 (Page 1 of 21)

Mydata TP9 feeders

Electronics Forum | Fri Feb 15 11:18:08 EST 2013 | richardc

Does anyone know the mechanical differences between a TPsys 1.6 version feeder and a 1.4. I only need to have one feeder for the 1.4 machine and would modify a 1.6 feeder if that is an option. Otherwise, does antone have a 1.4 version feeder they w

V-scoring design and equipment questions

Electronics Forum | Mon Jun 12 14:33:40 EDT 2006 | pjc

IPC spec is V-score shall not be more than 1/2 board thickness. They should be V scoring 1/4 off top and 1/4 off bottom equally.

tpsys 1.4.7 software

Electronics Forum | Mon Dec 04 18:12:45 EST 2006 | Say

Does anyone have a tpsys 1.4.7 software or the servo? Please contact me at sbounsavath@rad-tech.net or call me at 818-381-8500 ext.555. -Say

Re: 0201 components

Electronics Forum | Thu Feb 24 20:45:01 EST 2000 | Todd Woods

1.4 seconds. We found a step function decrease at 1 second.

Baking components at 70 degree

Electronics Forum | Wed Dec 19 14:02:18 EST 2007 | gersla

We decided to bake components in tray package at 70 Degree prior soldering. I am looking for suggestion regarding baking time for MSL3 components: Up to 1.4mm package thickness 1.4-2 mm thickness 2-4.5 mm thickness In JEDEC-033B this temperature is n

Universal GSM1 UPS Rev. 1.4

Electronics Forum | Mon Jun 26 03:00:15 EDT 2000 | armin

Hi, Anybody there running GSM1 UPS Rev 1.4 with OS/2 4.0 Warp ? We have OS/2 2.11 and we plan to upgrade to OS/2 4.0 Warp. I'm afraid of some incompatibility issues might occur. Please feedback any incompatibility issues you encountered in case you h

Milling durstone

Electronics Forum | Mon Dec 20 09:46:21 EST 2010 | azbvc

I have to make a few fixtures using durostone Material. I would like to know what end would be best to use for milling pockets out. I tried using HSS 1/4 in all I did was burn it up. Also I tried to use a 1/4 " carbide end and burnt that up too. any

Juki optimisation

Electronics Forum | Fri Mar 23 19:50:57 EDT 2007 | Frank

Possible head combinations to pick from multiple 12, 16, or 24mm feeders. Note: you can not mix feeder sizes for simultaneous picks. KE-2010 and KE-2050 will use 1&3, 2&4, or 1&4 KE-2020 and KE-2060 will use 1,3,R or 2,4,R or 1,4,R I prefer to s

ROHS replacment parts

Electronics Forum | Wed Jun 10 22:31:07 EDT 2009 | mgcoope

At work we use a system in which every customer uses a part with a phantom ( top level ) part and then under that we have more part numbers that are valid. So something like a surface mount resistor would be stored as something like. PPPPPPPPPPPP

Mass defect criterion

Electronics Forum | Thu Dec 12 21:44:15 EST 2019 | davef

I don't know what a "mass defect" is. Defects are within AQL [acceptable quality levels] or they aren't. I start at General Inspection Level 2 in the AQL Chart ANSI/ASQ STANDARD Z1.4-2006 and a sampling plan ANSI/ASQ Z1.4 Adjust the Level for Budge

  1 2 3 4 5 6 7 8 9 10 Next

1..4 searches for Companies, Equipment, Machines, Suppliers & Information